User manual DANBY DGR554LP

[. . . ] Pour effectuer des réparations ou obtenir l'adresse du service après-vente le plus proche, veuillez composer le NUMÉRO SANS FRAIS. Pour effectuer des réparations ou commander des pièces de rechange, veuillez donner les renseignements suivants : · Type de modèle · Numéro du modèle · Description des pièces Para obtener servicio, comuníquese con el establecimiento de servicio más cercano o llame al: Barril refrigerador El número de modelo se encuentra en la placa de serie, ubicada en el tablero posterior de la unidad. Puede comprar todos los repuestos o hacer un pedido especial visitando el establecimiento de servicio más cercano a su domicilio. Llame al TELÉFONO GRATUITO para obtener servicio de mantenimiento o la dirección del establecimiento de servicio más cercano a su domicilio. [. . . ] The protective plate also makes installation and removal of the keg stand easier. Installation of the Beer Keg: Position the keg stand directly in front of the open refrigerator cabinet. Using proper lifting technique, (using keg handles only) carefully lift the beer keg onto the keg stand. 7 NOTE: The keg stand is required when using 30 Liter (1/4 barrel) kegs only. To install the beer keg and stand inside the refrigerator cabinet, brace your knees behind the keg stand and grasp the keg stand handles. Lift the front of the keg stand just enough so that the front edge of the stand is resting on the front edge of the refrigerator cabinet. 8 Grasp the keg stand (front) handles and "care fully" slide the keg stand all the way into the refrigerator cabinet. Fig. Installation of the Keg Coupler: IMPORTANT NOTICE; Make sure the black pull handle of the keg coupler is in the "upward" (closed) position before installing on the beer keg. 9 Insert the keg coupler into the locking neck of the beer keg and apply a 1/4 turn clockwise to lock into position. Installation of the CO2 Air Line Hose to the Keg Coupler: Attach the open end of the (red) air line hose to the hose barb connection on the keg coupler. Secure hose by using the remaining (self locking) plastic snap on clamp provided. Readjust regulator pressure (D) (if necessary) between 10 ~ 12 psi/lbs. Open the secondary shut-off valve (C)by turning to "vertical" (north/south) position on lower stem pipe. D A E SETTING THE REFRIGERATOR TEMPERATURE: The temperature of the refrigerator compartment is controlled by adjusting/setting the thermostat control knob, located on the ceiling of the refrigerator cabinet. To start the refrigerator, and achieve maximum cooling quickly; · Turn the temperature control knob (using a coin or screwdriver) clockwise to the furthest (maximum) setting on the darker blue section of the graduated control dial. 14 · Allow the refrigerator to run at this setting for 3~4 hours. · When maximum cooling is achieved, turn back the temperature control knob setting to the 2:00 o'clock position on the graduated blue control dial. 15 · Correct cooling temperature is a key factor to consider in storing and dispensing draught beer. · Optimum temperature for serving draught beer is between 34ºF ~ 38ºF. (1ºC ~ 3ºC) Fig. 15 · To maintain temperatures ranging between 34ºF ~ 38ºF. (1ºC ~ 3ºC) We recommend the thermostat knob be positioned at the "2:00 o'clock" setting on the graduated blue control dial. 15 · To turn off the refrigerator, (no cooling) rotate the control knob to the "0" position. 14 8 HELPFUL HINTS ON CONTROLLING TEMPERATURE Keep a thermometer handy. (adjust temperature control knob accordingly) Periodically monitor temperatures inside your cooler. [. . . ] Close the connection between the beer keg and the keg coupler by pulling and lifting the handle into the upright position. Remove the beer tower assembly from the cabinet by grasping the center of the tower making a i turn counter clockwise and lift. Install the (2) cantilever wire shelves onto the factory installed cantilever support brackets located on the rear wall of the refrigerator cabinet. Please make sure all Chill 'N Tap accessories removed are stored in a safe place for future use. OPTIONAL ACCESSORIES FOR CHILL 'N TAP KEG COOLER: Description Beer Faucet Lock. [. . . ]