User manual DANBY DAR440BL

[. . . ] Once your unit is installed, keep the Use and Care Guide and this Installation Guide in a safe place for future reference. 1115R units are available in Black vinyl clad cabinets with matching doors and in Stainless models with a stainless steel door and handle, and a black cabinet. All 1115R Black unit doors have a slightly contoured handle across the top and are reversible. The black doors have recessed front panels that will accept a custom 1/4 inch thick door panel. [. . . ] Remove the grille and grille cap (two screws). Figure 6 ULIN_0122_A 5. Note that there may be a nut behind one or both screws on either side. Remove bottom hinge from cabinet (two screws) (Figure 5). 1 Figure 8 ULIN_0109_A www. U-LineService. com 6 07/2006 1115R and 1115WC Models 7. Relocate plastic spacer/bushing (Figure 8) on bottom of door to opposite side, and place door on bottom hinge pin. Clean out bushing hole in door bottom with a screwdriver if necessary. Hinge 12. Replace three plastic plugs removed in Step 10 into holes on top of unit. Replace screws in holes in bottom of unit on opposite side. Plastic Plug Hole Plastic Plug Hole 15. Be sure to place grille cap on opposite side of unit from where it was originally. Screw Right Side Door Swing Right Side Hinge Invert Screw Invert Hinge ULIN_0142_A Other Site Requirements Left Side Door Swing Power Supply The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current). Remove plastic hole plug (Figure 9) from door handle and relocate on opposite side. Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge. Environmental Requirements Many U-Line models are designed to operate in harsh outdoor/marine environments. Special considerations include the following: (1115R REFRIGERATOR requirements) · The units are designed to operate between 50°F (10°C) and 110°F (40°C). Go on to 5 Adjust Door. Wood Trim Finishing The U-Line Wine Captain® is equipped with woodtrimmed wine racks that are coated at the factory with a clear vinyl sealer, which will adequately protect the wood in normal usage. A final finish coat was not applied so that the wood trim could be stained to match décor. The trim on the racks may be coated with a final finish or stained. WARNING To prevent permanent damage to the inner liner of your unit, the wood trim MUST be removed from the unit for staining and/or finishing. Allow stain/finish to dry thoroughly (at least 24 hours per coat) in accordance with the product manufacturer's instructions prior to reinstallation. Failure to do so may cause the inner liner of the unit to have a permanent odor, which is not covered by the warranty. 07/2006 9 www. U-LineService. com 1115R and 1115WC Models If staining the trim is desired, it must be done before the application of any type of final finish. Review the following staining/final finish and final finish-only guidelines when staining and/or sealing the wood to ensure proper adhesion and durability of the finish. Remove all screws, securing wood trim to interior components, and remove the trim from the cabinet interior. Final finish-only application: 1. Remove all screws, securing wood trim to interior components, and remove the trim. A low-odor, water clean-up, quick-drying finish such as Minwax® Polycrylic® Protective Finish is recommended (Minwax® Polycrylic® is an ultra fastdrying, water-based finish). Apply a thin coat of a clear, protective finish, following the container label directions. Allow the final coat to dry for 24 hours IMPORTANT DO NOT use oil-based stains on wood trim. [. . . ] Apply two additional coats of the finish in the same manner, but do not sand the trim after the final third coat is applied. Allow the final coat to dry for 24 hours before reinstalling the trim to the cabinet interior components. . www. U-LineService. com 10 07/2006 1115R and 1115WC Models 5 Adjust Door 6 Prepare Power Supply Checking Door Alignment The unit's door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment or during door panel installation. Electrical Specifications CAUTION Electrical installation must observe all state and local codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician. [. . . ]