User manual DANBY DAC7077EE

[. . . ] If these suggestions do not solve the problem, contact an authorized service representative or call Danby TOLL FREE: 1-800-26-Danby CAUTION This symbol denotes a caution or warning Do not leave a room air conditioner unattended in a space where people or animals who cannot react to a failed unit are located. A failed unit can cause extreme overheating and fire in an enclosed, unattended space. SAVE THESE INSTRUCTIONS! 2 Electrical Specifications 1. All wiring must comply with local and national electrical codes and must be installed by a qualified electrician. If you have any questions regarding the following instructions, contact a qualified electrician. [. . . ] Be certain the proper electrical outlet is within reach of the installation. All wiring should be in accordance with local and national electrical codes. If it is necessary to use an extension cord to connect your air conditioner, use an approved "air conditioner" extension cord only. Your air conditioner may fail to operate in air containing oils (including machine oils), sulfide gas, near hot springs, etc. . . 5 30"(76. 2 cm) Min. Ground 20" (50. 8 cm) Min. Awning 12"(30. 5 cm) Min. 20" (50. 8 cm) Min. 2 Fence, wall, or other obstacle. 1. Assembly of the Upper Channel, to Cabinet. (Factory installed on some models) "L" Shaped Top Channel: Install the "L" shaped channel to the top of the cabinet as shown in Fig. 3 using four (4) 3/8"(9. 5mm) screws. 3/8" (9. 5mm) Screw 3a. Completing the Installation (cont'd) · Carefully place the air conditioner into the window with the "L" shaped mounting bracket (on top) positioned in front of the upper window sash. The bottom of the cabinet should be positioned on the "recessed" portion of the window frame. Pull the window down until it rests just behind the front flange of the (top) "L" shaped mounting bracket. Expand the shutter frames (fully) on each side and secure the top of the frames to the window sash using one 3/4" (19. 1 mm) screw on each side and one in the "L" shaped mounting bracket. 5 Secure the shutter clamp on each side of the (lower) shutter and secure to window sill using one 3/4" (19. 1mm) screw on each side. Fig. 5 Window Sash · · "L" Shaped Mounting Bracket · Fig. 3 "U" Shaped Channel (Factory Installed) 2. · Assembly of the Side Curtains to Cabinet. Extend the shutter from the shutter frame and slide it into the shutter guide on the side channel of the air conditioner as shown in Fig. Slide the shutters into the top ("L" Shaped) and bottom ("U" Shaped channels. The shutters are identified (on frame) as left & right. Sl id e 3/4" (19. 1mm) Screws · "L" Shaped Mounting Bracket Fig. 5 Shutter clamps do w n in to gu id e · Place the second foam sealing strip to fit the opening between the inside and outside windows then attach the safety lock to the outside window frame using one 3/4" (19. 1 mm) screw. 6 3. Completing the Installation Cut the foam (non adhesive) sealing strip to fit the area of the window sill that the air conditioner will rest on. 6 · PLEASE NOTE: Window applications come in a variety of different styles. Therefore, it may be necessary to modify or improvise your particular installation. Key Pad Features LED DISPLAY: Displays the following information independently; Set Temperature, Ambient Room Temperature and Auto Timer On/Off settings. POWER: Turns unit On / Off. MODE LED DISPLAY Temp/Timer Control 68 Auto Timer MODE: Allows you to scroll through and select the desired operating mode; Cool , Dry , Fan Only and *Auto Auto . *`Auto' is a pre-set factory program that automatically defines the mode (Cool or Dry) and fan speed based on the set temperature. [. . . ] Inadequate support. Odors. Formation of mold, mildew, or algae on wet surfaces. Water dripping outside. Low outside temperature. Condensation run-off is normal under these conditions. When outdoor temperature is approximately 65°F or below, frost may form when unit is in cooling mode. Remove and clean filter. Ice or frost build-up. Unit air filter is dirty. NOTES: 1. [. . . ]