User manual DANBY DAC7006DE

[. . . ] Your Owner's Instructions contains valuable information on using your air conditioner. Please take the time to read it as it will help you take full advantage of the unit's features. x The following figures are shown on pages from 4 to 6 : - View of the unit - Remote control(buttons and display) They will help you find the buttons and understand the symbols displayed. x In the main part of the installation book, you will find a series of step-by-step procedures for each function available. [. . . ] Result: x Each time you press the TEMPERATURE buttons: - The temperature is adjusted by 1°C - The indoor unit beeps x The air conditioner starts cooling, provided that the room temperature is higher than the selected temperature; the fan will, however, operate. 4 Select the fan speed by pressing the FAN button one or more times until the required setting is displayed: Automatic (rotated : Low Medium High Result: Each time you press the FAN button, the indoor unit beeps. ) 5 E-10 To control the direction of the air flow, refer to pages 16 and 17. Heating Your Room ENGLISH You must select the Heat mode if you wish to adjust the: x Heating temperature x Fan speed when heating 1 If necessary, press the Result: (On/Off) button. x The POWER indicator on the indoor unit lights up. x The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. IMPORTANT 2 If the is not displayed at the top of the remote control, press the MODE button on the remote control one or more times until it appears. You can change modes at any time. Note 3 To adjust the temperature, press the TEMPERATURE buttons one or more times until the required temperature is displayed. Result: x Each time you press the TEMPERATURE buttons: - The temperature is adjusted by 1°C - The indoor unit beeps x The air conditioner starts heating, provided that the room temperature is lower than the selected temperature; the fan will, however, operate. 4 Select the fan speed by pressing the FAN button one or more times until the required setting is displayed: Automatic (rotated : Low Medium High Result: x Each time you press the FAN button, the indoor unit beeps. x For the first 3 to 5 minutes, the fan does not operate until the air has been sufficiently warmed. Once the correct temperature has been reached, the fan will be automatically switched to the selected speed. ) 5 To control the direction of the air flow, refer to pages 16 and 17. E-11 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. 1 If necessary, press the Result: (On/Off) button. x The POWER indicator on the indoor unit lights up. x The air conditioner starts up in the mode selected when the unit was last used. Note If you wish to switch the unit off at a specific time, refer to page 19. 1 If the or is not displayed at the top of the remote control, press the MODE button on the remote control one or more times until it appears. x The air conditioner will be controlled as indicated in the illustrations below. Cooling The desired temperature is increased by 1°C every hour. When it has been increased by 2°C (after two hours), the temperature is maintained for four hours. Heating The desired temperature is decreased by 1°C every hour. When it has been decreased by 2°C (after two hours), the temperature is maintained for four hours. To Cancel the Sleep Timer If you no longer wish to use the Sleep Timer that you have set, you can cancel it at any time. The air conditioner operates normally. E-20 Operating Recommendations ENGLISH Here are a few recommendations that you should follow when using your air conditioner. Topic Heating performances Recommendation The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors. If the temperature of the outside air drops, the air conditioner will heat less. If you find that the room is not warm enough, use an additional heating appliance. The air conditioner circulates warm air to heat your room; as a result, some time will be required after starting the air conditioner to warm the entire room. If necessary, set the air conditioner on before you wish to use the room. When outside temperatures are low and humidity is high, frost may form in the outdoor unit when heating is selected. [. . . ] x Check that the POWER indicator on the indoor unit is on; if necessary press the (On/Off) button on the remote control. x Check whether the TIMER indicator on the indoor unit is switched on. If so: - Wait until the switch-on time is reached and the air conditioner starts up automatically - Cancel the timer (see pages 18~20 for further details) x Check that there are no obstacles between you and the indoor unit. x Check that you are close enough to the indoor unit (seven metres/ yards or less). [. . . ]