User manual DANBY DAC6003D

[. . . ] x The number of the battery life indicator means the remaining battery life. Replace the batteries when only one battery life indicator remains. E-6 Inserting the Remote Control Batteries ENGLISH You must insert or replace the remote control batteries when : x You purchase the air conditioner x The remote control does not work correctly Note x x x x Use two AAA, LR03 1. 5V batteries. Batteries may be completely discharged after 12 months, even if they have not actually been used. 1 Remove the battery cover in the rear of the remote control by pushing it with your thumb. 2 Insert two batteries, respecting the polarities as indicated by the + and - symbols. 3 Close the cover by sliding it back in its place. E-7 Getting Start The User's Manual provides you valuable information about your air conditioner. It will help you take full advantage of the unit's features. You have already seen the basic description of the unit on pages from 4 to 6. [. . . ] x If the room temperature reaches 3°C lower than the set temperature, the air conditioner starts heating again. button to select the fan speed until the required setting Automatic (rotated : Low Medium High Maximum Result: x Each time you press the button, the indoor unit beeps. x For the first 3~5 minutes, the fan may not operate to prevent the cool air from running out of the indoor unit. ) 4 Press the is displayed. 5 To control the airflow direction, refer to pages 16 and 17. E-11 Selecting the Dry Mode You can select the Dry mode if you want to dehumidify your room. 1 If necessary, press the Result: button. x The operation indicator on the indoor unit lights up. x The indoor unit beeps. 2 Press the Result: button on the remote control until is displayed. button. x The indoor unit beeps each time you press the x The air conditioner runs in the Dry mode. Note You can change modes at any time. 3 Press the button to adjust the temperature until the required temperature is displayed. Result: x Each time you press the button: - The temperature is adjusted by 1°C - The indoor unit beeps x The air conditioner starts dehumidifying and the fan speed is adjusted automatically. 4 To control the airflow direction, refer to pages 16 and 17. E-12 Selecting the Fan Mode ENGLISH You can select the Fan mode if you want to ventilate your room. 1 If necessary, press the Result: button. x The operation indicator on the indoor unit lights up. x The indoor unit beeps. 2 Press the Result: button on the remote control until is displayed. button. x The indoor unit beeps each time you press the x The air conditioner runs in the Fan mode. 1 Press the Result: button until the indicator appears on the remote control. x The indoor unit beeps. x The air conditioner turns off after an hour automatically. 2 Press the button until the desired mode is displayed at the remote control to select the mode after setting the 1 Hour Timer. Result: The air conditioner operates in the selected mode for an hour. Note If you set the 1 Hour Timer when the air conditioner is turned off, the air conditioner turns on and operates for an hour. To cancel the 1 Hour Timer Press the Result: button to cancel the 1 Hour Timer. x The air conditioner operates normally. E-21 Operating Recommendations When you use your air conditioner, it is recommended to read the following : Topic Heating capacity Recommendation The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors. If the temperature of the outside air drops, the air conditioner heats less. It will take some time to warm the air in your room entirely after the air conditioner turns on. When you select the Heat mode, frost may form in the outdoor unit due to the low temperature and high humidity. After about 7 minutes, the air conditioner starts operating again normally. If both the indoor and outdoor temperatures are high when you select the Heat mode, the fan and the compressor of the outdoor unit may stop at times. If power failure occurs when the air conditioner is operating, the air conditioner turns off. When the power returns, the air conditioner starts up again automatically. [. . . ] x Check if the air filter is dirty; refer to page 25 for cleaning instructions. x If the airflow is directed upwards, set the blade downwards with the remote control. x Check if the mode is set to the Auto, Cool, Heat or Fan mode; in the Dry mode, the fan speed changes automatically. x Check if the air conditioner has been turned on; if necessary, press the button on the remote control. The air conditioner does not operate with the remote control. No beep is heard when you press the on the remote control. [. . . ]