User manual CYBEX INTERNATIONAL FT 325

[. . . ] Part Number 18010-999-4 Cybex Bravo Press Owner's Manual Strength Systems www. cybexintl. com Table of Contents Safety Safety Guidelines And Practices . . 26 26 27 28 28 Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. DISCLAIMER: Cybex International, Inc. , makes no representations or warranties regarding the contents of this manual. We reserve the right to revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such revisions or changes. [. . . ] Do not install, use, or store the unit in an area of high humidity, such as near a steam room, sauna, indoor pool or outdoors. Extensive exposure to water vapor, chlorine and/or bromine could adversely affect the equipment. 10 Cybex 18010 Bravo Press Owner's Manual Assembly Procedure Two people will be required for this procedure. Read and understand all instructions thoroughly before assembling this unit. If there is damage, see the Customer Service section of this manual for proper procedure to return, replace, or reorder parts. Qty 4 Part Number 16010-311 Description Foot pad Diagram 2 4800-557 Decal (10-150) 2 GQ000206 Link 2 18010-007 Handle Assembly Placement If Then Two people will be required for this procedure 1. Attach foot pads to each foot of frame. 18010canfitthrough doorway 11 Cybex 18010 Bravo Press Owner's Manual If Then Two people will be required for this procedure 1. Remove back panels from machine. 18010cannotfit through doorway 4. Remove spiral pin connecting pulley using a hammer and a 3/16" pin punch. Spiral pin 6. Guide rod cap contains a compression spring that will fly if grasp is not released slowly. Slide spring loaded guide rod cap down guide rod until cap is clear of frame. Slowly release grasp of guide rod cap and remove. 12 Cybex 18010 Bravo Press Owner's Manual If 8. Loosen the two button head socket cap screws (BHSCS) securing handle bar to frame using a 7/32" Allen wrench. Threaded block 13 Cybex 18010 Bravo Press Owner's Manual If Then 4. Remove BHSCS and locknuts, remove one side of mounting tube using a 7/32" Allen wrench and a 9/16" wrench. Mounting Tube 18010cannotfit through doorway 5. Place two drops of Loctite® 242 to each BHSCS and in thread holes of threaded block for handle bar. Securelyanchormachinetothefloor To maximize stability, equipment must be secured to a solid level surface. · Cybex · Use · If is not responsible for the actual anchoring of equipment. tensile capacity (3/8'' grade 2 bolts or better). legs/frame does not contact surface, DO NOT pull down with anchors. Shim any leg or framenotincontactwithsurfaceusingflatwashers. 14 Cybex 18010 Bravo Press Owner's Manual Install individual weight plates one at at time 1. Position each weight plate so wide edges of bushings face upward and narrow edges of bushings face downward. RE COR CT WRO NG Wide bushing edge faces upward 2. Snap guide rods in to position Cable routing The narrow bushing edge must face downward. 1. Attach pulley mount to lifting post using a hammer and spiral pin. Spiral pin 5. Lift top weight up and down simulating normal operation (without selecting any resistance). [. . . ] To speak with a customer service representative, call 888-462-9239 (for customers living within the USA) or 508-533-4300 (for customers outside the USA). The following information located on the serial number decal will assist our Cybex representatives in serving you. · Unit Serial Number, Product Name and Model Number This product may be produced under one or more of the following patents Made in U. S. A. MODEL# 8810-90 SERIAL# XXXXXXXXXXXXX 1 9 7 5 2 4 th Av e S W O w a to n n a , MN . 5 5 0 6 0 1-888-462-9239 5, 628, 715 5, 722, 921 6, 743, 158 7, 338, 415 D481, 428 D490, 128 D491, 238 7, 727, 128 5, 643, 152 5, 620, 402 7, 179, 209 7, 503, 882 D486, 535 D490, 865 D497, 190 7, 717, 831 5, 616, 107 6, 488, 612 7, 335, 139 D480, 773 D490, 127 D491, 237 6, 033, 350 · · · · Part Description and Part Number if you have it. [. . . ]