User manual CYBEX INTERNATIONAL 14220 CABLE COLUMN

[. . . ] Cybex Total Access Cable Column Owner's and Service Manual Strength Systems Part Number 14220-999-4 E www. cybexinternational. com Cybex Total Access Cable Column Owner's and Service Manual Strength Systems Part Number 14220-999-4 E Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. VR3® and its mark are registered trademarks of Cybex International, Inc. DISCLAIMER: Cybex International, Inc. , makes no representations or warranties regarding the contents of this manual. We reserve the right to revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such revisions or changes. 10 Trotter Drive Medway, MA 02053 · 508-533-4300 · FAX 508-533-5183 www. cybexinternational. com · techhelp@cybexintl. com · 14220-999-4 E Table of Contents Front Pages Table of Contents . [. . . ] Read and understand all instructions thoroughly before starting any of the procedures listed on this instruction sheet. WARNING: Use extreme caution when removing shipping cones and installing feet. With an assistant, carefully remove each (standard) cone-shaped shipping support using a 3/4" socket or wrench. Carefully place rubber feet (supplied with machine) on each foot of the frame. Using a 1/8" Allen wrench, remove the two Button Head Socket Cap Screws (BHSCS) securing the bottom bracket to the frame. NOTE: After final BHSCS is removed shroud will slide down to the floor with bottom support bracket attached. 30 50 70 90 110 130 150 170 190 210 230 250 270 290 310 330 350 370 390 410 430 450 470 490 14 23 32 41 50 59 68 77 86 95 104 113 122 131 140 149 158 167 176 185 194 203 212 221 Assembly Page 4-1 Cybex Total Access Cable Column Owner's Manual D. Slide spring loaded top guide rod cap down guide rod until guide rod cap is clear of frame. NOTE: Guide rod cap contains a compression spring that will fly if grasp is not released slowly. Carefully lean guide rods slightly outward, away from machine to clear pulley. NOTE: Excessive pressure on guide rods may damage lower guide rod caps. J. Carefully hang over top of machine so cables and top weight are out of the way when installing weight plates. Carefully align weight plate over guide rods and slowly lower weight plate. NOTE: When installing weight plates, position plates so wide edges of bushing face upward and narrow edges of bushing face downward. See Figures 1A and 1B. OR C CT RE WIDE bushing edge faces upward W NG RO NARROW bushing edge NOTE: The narrow bushing edge must face downward. Figure 1A N. Place springs and guide rod caps on guide rods (removed from step 5G). Compress guide rod caps and ailgn guide rod caps with weight frame holes and secure in place. NOTE: Guide rod caps must snap or lock into weight frame holes. Assembly Page 4-2 Cybex Total Access Cable Column Owner's Manual 6. Without selecting any resistance, lift top weight up and down (simulating normal operation). Have an assistant verify that the cable is moving smoothly and is routed straight from the top of pulley bracket to the top weight. Starting at the bottom replace the two BHSCS (removed in step 5D) to secure bottom support bracket to the shroud. NOTE: When peeling off back cover, make sure that the decals remain attached to the front sticker. NOTE: A guide pin can be anything that fits the weight stack hole, such as a weight selector pin. [. . . ] AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these could scratch or damage the equipment. Maintenance Page 5-6 Cybex Total Access 14220 Cable Column Owner's Manual 4. Guidelines for cleaning front panel: · · · · · · · Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing. Don't apply cleaners in direct sunlight or at elevated temperatures. Compatible Cleaners and Detergents: · · · · · Formula 409 Top Job Joy Palmolive Windex with Ammonia D 6. [. . . ]