User manual CYBEX INTERNATIONAL 12231 DIP CHIN

[. . . ] Cybex VR3® Dip/Chin Assist Owner's Manual Strength Systems Part Number 12231-999-4 D www. cybexinternational. com Cybex VR3® Dip/Chin Assist Owner's Manual Strength Systems Part Number 12231-999-4 D Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. VR3® and its mark are registered trademarks of Cybex International, Inc. DISCLAIMER: Cybex International, Inc. , makes no representations or warranties regarding the contents of this manual. We reserve the right to revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such revisions or changes. 10 Trotter Drive Medway, MA 02053 · 508-533-4300 · FAX 508-533-5183 www. cybexinternational. com · techhelp@cybexintl. com · 12231-999-4 D Table of Contents 1 Safety Safety. [. . . ] WARNING: Use extreme caution when removing shipping cones and installing feet. With an assistant, carefully remove each (standard) cone-shaped shipping support using a 3/4" socket or wrench. Carefully place rubber feet (supplied with machine) on each foot of the frame. Carefully remove hardware kit, chin handle and support leg secured to frame. NOTE: If holes do not line up then loosen the 12 Button Head Socket Cap Screws (BHSCS) securing dip handle to frame. NOTE: BHSCS . 375-16 x . 625 are installed on the inside of connection plate. BHSCS 3. 75-16 x . 875 are installed on the outside of connection plate. BHSCS . 375-16 x . 875 (6) 86. 5 Chin Handle BHSCS . 375-16 x . 625 (6) Connection Plate Dip Handle Figure 1 Assembly Page 4-1 112 10 44 27 78 95 52. 5 Cybex VR3 12231 Dip/Chin Assist Owner's Manual D. Using a 7/32" Allen wrench (supplied in kit) securley tighten all BHSCS securing chin handle in place. If BHSCS securing dip handle were loosened in step 5B then remove one BHSCS, apply loctite to hole in connection plate and BHSCS and then reinstall BHSCS. Repeat this step until all 12 BHSCS are loctited then securley tighten all BHSCS. NOTE: Do not remove all BHSCS at the same time as connection plate will fall. Place locknuts on BHSCS and securely tighten with a 9/16" Support Leg wrench and 7/32" Allen wrench. Using a 1/8" Allen wrench, remove the two Button Head Socket Cap Screws (BHSCS) securing the bottom bracket to the frame. NOTE: After final BHSCS is removed shroud will slide down to the floor with bottom support bracket attached. Slide spring loaded top guide rod cap down guide rod until guide rod cap is clear of frame. NOTE: Guide rod cap contains a compression spring that will fly if grasp is not released slowly. Carefully lean guide rods slightly outward, away from machine to clear pulley. NOTE: Excessive pressure on guide rods may damage lower guide rod caps. J. Carefully align weight plate over guide rods and slowly lower weight plate. NOTE: When installing weight plates, position plates so wide edges of bushing face upward and narrow edges of bushing face downward. Place springs and guide rod caps on guide rods (removed from step 7G). [. . . ] Never use harsh solvents or cleaners which are intended for industrial applications. CYBEX and its vendors cannot be held responsible for damage or injuries resulting from the use or misuse of cleaning products. Frames - Wipe down all frames using a mild solution of warm water and car wash soap. AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these could scratch or damage the equipment. [. . . ]