User manual CTX PV720A

[. . . ] The purchase of TCO99 compliant monitors contributes to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. In many countries, environmental labelling has become an established method-for encouraging the adaptation of goods and services to the environment. The main problem, as far as computers and other electronics equipment are concerned, is that environmentally harmful substances are used both in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature. [. . . ] Without applying excessive pressure clean the screen with the slightly dampened rag. Exposing the Monitor to rain, water, moisture or sunlight can severely damage it. Make sure the cord is placed in an area where it will not be stepped on. Servicing of any nature should only be performed by an authorised technician. Safe storage of the LCD Monitor is in a range of minus 20 to plus 65 degrees Celsius. Storing your LCD Monitor outside this range could result in permanent damage. If any of the following occurs immediately unplug your Monitor and call an authorized technician. · · The power or Monitor-to-PC signal cord is frayed or damaged. Liquid has been spilled into the Monitor, or it has been exposed to rain. · The Monitor has been dropped or the case has been damaged. 8. For use only with power supply: · · · · FSP Electronic Co. , Ltd. Type LA-40M-112 Notice : Actual safety specifications please refer to the label on the back of monitor. 7 PV720A User's Manual Introduction Product Description Congratulations on purchasing this new generation monitor. Your LCD monitor incorporates high quality display into a small lightweight module. It has power- saving capabilities and emits no X-ray radiation. The features are: · · · · · · · · · 17" TFT Liquid Crystal Display Compatible with IBM VGA, VESA Direct RGB input SXGA 1280x1024 resolution Lightweight compact design, weighing less than 7. 5Kg DPMS (power saving) Universal adapter power supply Anti-glare display On-Screen Display (OSD) controls and adjustments Package Overview Your monitor package contains: LCD Monitor 8 PV720A User's Manual User's Guide / Driver CD Power Cord Power Adapter D-Sub 15 VGA Signal Cable 3. 5 mm Audio Cable Speaker Box CAUTION Keep the shipping carton in case the need arises to store or transport the unit. Let the LCD lie on its face when you put it into the carton. 9 PV720A User's Manual Installation & Remove 1-1. Rotating to the mode "Portrait" (vertical orientation) 3-1. Installing VESA-compliant Connecting Device* This product provides square screw holes that conform to 100mm*100mm VESA-compliant connection interface. 11 PV720A User's Manual 3-2. Remove VESA-compliant Connecting Device* *User should prepare the connection device for VESA themselves. Connect (1) the video signal cable of the monitor to the 15-pin connector of the video port in your computer. With the monitor switched off, attach (2) the power cord to the monitor and then to a grounded power outlet. 12 PV720A User's Manual 4. Connect your audio cable one end to the external speaker, through the connector of audio input on the rear part; the other end to audio device (such like connector of the sound card in the PC). 5. If necessary, adjust the front panel controls according to your personal preference. 13 PV720A User's Manual Recommended Use of the Monitor Power Use the type of power indicated on the marking label. Plugs Do not remove any of the prongs of the monitor's three-pronged power plug. [. . . ] If the problem persists please contact your local dealer or our service center. The monitor does not respond after you turn on the system. Check if the monitor is turned on. Turn off the power and check the monitor power cord and signal cable are properly connected. The characters on the screen are dim. Refer to the Controls and Adjustments section to adjust the brightness (BRIGHTNESS on the OSD sub-menu. ) . The screen is blank. During use the monitor screen may automatically turn off as a result of the Power Saving feature. Refer to the Controls and Adjustments section to adjust the brightness (BRIGHTNESS on the OSD sub-menu. ) . The screen flashes when it initializes. Turn off the monitor and turn it on again. Refer to the Controls and Adjustments section to reload the default setting (RESET on the OSD main-menu. ) . Partial image or incorrectly displayed image Check to see if the resolution of your computer is higher than that of the LCD display. [. . . ]