User manual CREATIVE SOUND BLASTER X-FI GO! PRO GUIDE DE DÉMARRAGE RAPIDE

[. . . ] It can be used without manual pairing. Using Your Audio Device 7 The Zone feature enables you to stream music to a maximum of four selected wireless receivers and/or supported devices. It requires manual pairing and each device is assigned to an available zone. For more information on using the broadcasting and zone control features, see "Using the Wireless Features" on page 11. NOTE * Available separately or may be bundled with your audio device. Expand your wireless system by adding on other Sound Blaster Wireless devices. [. . . ] NOTE · Clicking the Restore Defaults button in the Sound Blaster Wireless Control Panel restores the default audio settings, sets the RF channel to Auto and enables the Wireless Music Control. · Refer to your receiver's documentation for additional information. Troubleshooting 16 Troubleshooting Problems with Multiple Audio Devices The onboard audio chipset seems to be in conflict with Sound Blaster Wireless Transmitter. Disable your notebook's onboard audio chipset. See your notebook's motherboard documentation for details Problems with Sound No sound from the headphones. Check that the headphones are connected to the Headphone/Line Out jack. No audio output when playing digital files such as . WAV, MIDI files or AVI clips. Check the following: · The powered speakers or external amplifier are turned on and connected to the audio device's Headphone jack. · The speakers' volume control knob, if any, is set at mid-range. · There is no hardware conflict between the card and a peripheral device. Problems with Wireless Features The wireless connection does not seem to work. Do the following: · Check that your transmitter and your paired devices are turned on, and your transmitter's wireless features are enabled. · In case of configuration issues, you can fully reset your wireless system by clicking the Reset all Zones button in the Sound Blaster Wireless Control Panel, and then manually pair your receivers again. Troubleshooting 17 The receivers seem to be picking up extra noise, or there are intermittent pauses. The position of your Sound Blaster Wireless devices as well as signals from other wireless routers or Bluetooth equipment may affect the quality of the transmissions. Try the following: · In the Sound Blaster Wireless Control Panel, change the RF Channel from Auto to either Ch 1, 2 or 3. Use the extension cradle for more flexibility in placing your transmitter. · Place your transmitter away from other devices that transmit wireless signals, and away from large metal surfaces. · Reposition your devices so that there are fewer objects (for example, multiple walls or large metal structures) between them. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation. CAUTION: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules, this device must be installed with computer equipment certified to comply with Class B limits. All cables used to connect to the computer and peripherals must be shielded and grounded. Operation with non-certified computers or non-shielded cables may results in interference to radio or television reception. MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the device. [. . . ] Toute modification non approuvé explicitement par le fournisseur de licence de l'appareil peut entraîner l'annulation du droit de l'utilisateur à utiliser l'appareil. Regulatory Information 25 European Compliance This product conforms to the following: EMC Directive 2004/108/EC. Mains operated products for the European market comply with Low Voltage Directive 2006/ 95/EC. Communication / RF wireless products for the European market comply with R&TTE Directive 1999/5/EC. CAUTION: To comply with the Europe CE requirement, this device must be installed with CE certified computer equipment which meet with Class B limits. [. . . ]