User manual CREATIVE GIGAWORKS T40 QUICKSTART BACK

[. . . ] - This fuction does not work for this monitor. 7) VOL Adjusts the audio volume. 8) MUTE Pauses (mutes) the audio output temporarily. The audio resumes if MUTE or - VOL + is pressed in the Mute mode. 9) TTX/MIX TV channels provide text information services via teletext. - This fuction does not work for this monitor. 10) MENU Opens the on-screen menu and exits from the menu screen or closes the screen adjustment menu. 11) ENTER Activates a highlighted menu item. 12) P. MODE When you press this button, current picture mode is displayed on the lower center of the screen. AV / S-Video / Component : P. MODE The Monitor has four automatic picture settings that are preset at the factory. [. . . ] The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. 29) SIZE Switches the PIP Picture Size. 30) REW Rewind 31) STOP Stop 32) PLAY / PAUSE Play/Pause 33) FF Fast forward © 1995~2007 CREATIVE. ALL Rights Reserved Select Language Main Page Model Safety Instructions Introduction Connections Installing the Stand KIT Connecting the LCD Display Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement. Connections Installing the Stand KIT Note · Only the supplied bolts should be used. Caution Samsung Electronics will not be responsible for damages caused by using a base other than those specified. Installing the Semi Stand Left stand Right stand Caution Make sure to install the stand with the Caution label folded backwards. 1) To protect your product, a Cover Hole is included as an accessory. This protects the hole at the bottom of the monitor where the stand is inserted. If you install a wall mount kit for your monitor, please place the Cover Hole over it. 2) Insert it into the hole at the bottom of the monitor. Insert the screw provided with the Cover Hole into the marked place and fasten it firmly. Caution The resolution may differ for each product model. For information on the optimal resolution, refer to the user manual. Connecting the LCD Display Using a Power cord with Earth In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance. Note · AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the User Controls under Adjusting Your LCD Display. Connecting a Computer 1) Connect the power cord for your LCD Display to the power port on the back of the LCD Display. Trun on the power switch. 2) There are 3 ways to connect the D-sub to your LCD Display. (If it does, request an a service for the main board of the computer. ) 3) 4) If you installed a new video card or if you assembled the PC, check if you installed the Adaptor(video). Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz. (Do not exceed 60Hz when using the maximum resolution. ) 5) If you have problems in installing the Adaptor (video) driver, boot the computer in Safe Mode, remove the Display Adaptor in the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the Adaptor (video) driver. Check List Note · The following table lists possible problems and their solutions. Before calling for assistance, check the information in this section to see if you can remedy any problems for yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. · For more network-related information, refer to the MagicNet Troubleshooting section. Problems related to the Installation (PC Mode) Note · Problems related to the LCD Display installation and their solutions are listed. Problems Solutions Check if the signal cable between the computer and the LCD The LCD Display screen flickers. Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note · Problems related to the LCD Display screen and their solutions are listed. Problems The screen is blank and the power indicator is off. Solutions Ensure that the power cord is firmly connected and the LCD LCD Display is on. (Refer to the Connecting the LCD Display ) "Check Signal Cable" message. Ensure that the signal cable is firmly connected to the PC or video sources. (Refer to the Connecting the LCD Display ) Ensure that the PC or video sources are turned on. "Not Optimum Mode " message. Check the maximum resolution and the frequency of the video Adaptor. Compare these values with the data in the Preset Timing Modes Chart. The picture rolls vertically. Check if the signal cable is securely connected. (Refer to Connecting a Computer) The image is not clear; picture is blurred. Run Frequency Coarse and Fine tuning. [. . . ] Enter the BIOS menu of your set by pressing the F2 key in the BIOS logo screen. Then, enable the USB Boot First option by selecting that option and pressing the Enter key in the Boot menu. Switch your set on while your USB disk is connected and boot up in DOS mode. Run C:\ghost. exe and choose Local Partition From Image from the menu. [. . . ]