User manual CREATIVE DESKTOP WIRELESS 6000

[. . . ] i Document Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii 1 About Creative Wireless Keyboard and Optical Mouse Creative Wireless Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Creative Wireless Optical Mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Creative RF Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 3. Insert two AA batteries according to the directions in the battery compartment, as shown in Figure 2-2. Close the battery compartment cover and push the catch downwards to lock it. Figure 2-2: Inserting batteries Installing Hardware 2-1 Step 2: Insert batteries into Creative Wireless Keyboard 1. Slide the battery compartment cover downwards as shown in Figure 2-3. Figure 2-3: Opening the battery compartment 3. 4. Insert two AA batteries according to the directions in the battery compartment, as shown in Figure 2-4. Slide the battery compartment cover upwards to close it. Figure 2-4: Inserting batteries Installing Hardware 2-2 Step 3: Connect the Creative RF Receiver 1. Connect the USB connector on the RF receiver to the USB port on your computer as shown in Figure 2-5. Make sure that you have inserted batteries into the mouse and keyboard before Step 3. Figure 2-5: Connecting the RF receiver to the computer 3. Place the RF receiver at least 8 inches (20 cm) from your computer or monitor. Installing Hardware 2-3 Step 4: Activate the wireless desktop devices · Make sure that the keyboard and mouse are within 1. 8 meters (6 feet) of the RF Receiver. · Press the Connect buttons on each of your Desktop Wireless 6000 devices, as shown in Step 4, each time you insert batteries. · Make sure you press the Connect buttons on the keyboard and mouse within 10 sec after you press the Connect button on the RF Receiver. 1. 3. Press the Connect button on the RF receiver, as shown in Figure 2-6. The Communication LED indicator on the RF receiver blinks green for about 5 sec. The Communication LED indicator on the RF receiver blinks green for about 5 sec. 1 2 3 Figure 2-6: Activating the Creative keyboard and mouse Step 5: Test the keyboard and mouse To install drivers, refer to "Installing Software" on page 3-1. Move the mouse cursor or press a key on the keyboard to test that the keyboard and mouse are connected. If nothing happens, repeat Step 4. Installing Hardware 2-4 3 Installing Software Installing Software Installing Software Windows 98 and 98 SE users may be prompted by an Add New Hardware Wizard dialog box when Windows detects a USB device. You may need to insert the Windows Installation CD into the CD-ROM drive during installation. Some computers may be supplied without the Windows CD, but have the necessary files stored in c:\windows\ options\cabs (replace c:\ with the drive letter your Windows has been installed on). You need to install software to use Creative Desktop Wireless 6000. The following instructions are applicable to Windows 98, Windows 98 Second Edition (SE), Windows Millennium Edition (Me), Windows 2000 and Windows XP. After you have connected Creative Desktop Wireless 6000, Windows will detect the USB device and install the required drivers automatically. Insert the Creative Desktop Wireless 6000 Installation CD into the CD-ROM drive. The CD supports Windows Autoplay mode and starts running automatically. In the Run dialog box, type d:\ctrun\start. exe (replace d:\ with your CD-ROM drive letter) Select the applications to install, and then click the OK button. [. . . ] · Make sure that there is a connection between the RF receiver and keyboard or mouse. For more information, refer to "Step 4: Activate the wireless desktop devices" on page 2-4. Do one or more of the following: · Make sure that the RF receiver is connected correctly to your computer. · Make sure that the batteries have been inserted properly and according to the directions shown in the battery compartment. [. . . ]