User manual COMPRO V550 START UP GUIDE

[. . . ] COMPRO makes no warranties with respect to this documentation and disclaims any implied warranties of merchantability, quality, or fitness for any particular purpose. COMPRO reserves the right to make revisions to this publication without obligation to notify any person or entity of any such changes. +886 2 2918 0169, Fax +886 2 2915 2389 3/F, No. 12, Alley 6, Lane 45, Pao Shin Road Hsintein City, Taipei, Taiwan. www. comprousa. com Table of Contents About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After you have connected the power adaptor, you will see orange light shining out from the side. Press the Power switch at the top will turn on the TV Box and you will see orange light become blue light. If you have connect V550 TV box to your computer's video card, press the power button on the TV box or the power button on the remote control will switch between TV and PC signal. You may also press "TV/PC" button on the remote control to achieve the same result. Order of the Sources: TV > Composite > S-Video > Component > TV VideoMate V550 TV Box supports 7 resolutions from below. Resolution 1 -> 640*480 (4:3) Resolution 2 -> 800*600 (4:3) Resolution 3 -> 1024*768 (4:3) Resolution 4 -> 1280*1024 (5:4) Resolution 5 -> 1280*720 (16:9) Resolution 6 -> 1440*900 (16:10) Resolution 7 -> 1600*1200 (4:3) To change resolution, please open up menu and select the resolution you want. "RES" button from the remote controller can also switch the resolution. OSD Menu Guide Menu button will open up OSD Menu, please use the direction key to navigate. (Picture) Brightness Contrast Saturation Sharpness Hue Y/C Sep. Mode Reset 6 (TV) (Monitor) (OSD) (Sound) Adjust the brightness (0~100) Default : 50 Adjust the Contrast (0~100) Default : 50 Adjust the Saturation (0~100) Default : 50 Adjust the Sharpness (0~15) Default : 0 Adjust the Hue ( 0~100) Default : 50 Choose between 2D/3D mode Default : 3D Mode Reset Picture Settings (Picture) Input Signal Channel Rename Fine tune Auto Scan Channel Swap CH Add/Erase Channel Video System (TV) (Monitor) (OSD) (Sound) Select Air or Cable for TV input signal type. PAL (B/G, D/K, I) SECAM (B/G, D/K) Default is SECAM D/K (Picture) Resolution Refresh Rate Noise Reduction Display Type Input Source (TV) (Monitor) (OSD) (Sound) 640*480 800*600 1024*768 (default) 1280*720 1280*1024 1440*990 1600*1200 60Hz (default) 75Hz Adjust level of noise reduction. (0~8) Default is 4 LCD (default) CRT PDP TV Composite SV (S-Video) YCbCr (Component) PC (Picture) (TV) (Monitor) (OSD) (Sound) OSD Position Press OK key, use direction keys to move OSD position OSDTransparency 1 2 3 4 Language Select your language (Default language is Russian) Reset All Settings NO/YES (1 Cancel / 2 Reset All Settings) Information VideoMate V550 Version information Country/Region Select your country or region (Default country is Russia) (Picture) Volume Treble Bass Loudness Reset (TV) (Monitor) (OSD) (Sound) Adjust volume (0-50) Adjust Treble volume (0-15) Adjust Bass volume (0-15) ON (enlarge the amplifier) / OFF (original signal) Reset sound settings (NO/YES) 7 Channel Swap To swap the channel numbers, please select Channel Swap from the menu then select yes, and it will show as a sub menu. You may browse with the direction keys; Up and Down are going through the list while Left and Right are changing pages of the list. Select the channel number that you wish to swap and press OK, and then enter the number of the channel that you wish to switch. To reset to the original channel numbers, please rescan the channel table again by selecting Auto Scan in the menu. My Favorite Channel List My Favorite Channel List can store up to 10 channels that you watch the most and browse with "FAV UP" and "FAV DOWN" keys on the remote controller. To add channels to the favorite list, please turn to the channel you wish to add and press "SET FAV" on the remote controller. Press "OK" on the selected position. PIP (Picture In Picture) You can start PIP function by clicking "PIP" button on the remote control. When PIP is working, press "PIP" button again will change the size of the TV screen; you may zoom twice and the third time you press "PIP", it will close the PIP function. And you can move the TV screen position with the blue arrow button on the remote. Channel Surfing Channel Surfing allows you to preview and find the channel you want by presenting in 9 squares. To access this function, please press "CH. SURF" button on the remote controller. When you have found the channel you prefer, please press the correspondent number keys (1~9) to switch to that channel. 8 Troubleshooting Installation The most common cause of the problem is the incorrect connection of the cables. [. . . ] Also make sure computer grounding is good. Why does the remote control fail? Please make sure you have put the batteries to the remote control. Please aim at the TV box and you should see the blue light flashes when you press the remote controller. Contacting Compro Technical Support Before you submit an email for support, please check support FAQs on our web site. http://www. comprousa. com/support You can download the latest update from our website. When contacting Compro for technical support, please use the Compro support request form and provide as much of the requested information as possible. [. . . ]