User manual COBRA XRS 970
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual COBRA XRS 970. We hope that this COBRA XRS 970 user guide will be useful to you.
Manual abstract: user guide COBRA XRS 970
Detailed instructions for use are in the User's Guide.
[. . . ] Introduction
Important Information and Customer Assistance
·
Important Information
Federal Laws Governing the Use of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra radar/ laser detector. The Communications Act of 1924 guarantees your right to receive radio transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action. Operating Instructions Safety/Strobe Alert Use of this product is not intended to, and does not, ensure that motorists or passengers will not be involved in traffic accidents. [. . . ] Before IntelliMute Pro can be turned On, you must have turned On and Set the IntelliMute activation point. (See pages 14 through 16. ) CAUTION When IntelliMute Pro is On, NO radar signals will be detected and NO alerts will be given at RPMs below the IntelliMute activation point.
To Turn IntelliMute Pro On or Off Using Program Mode
(See Page 7 For Instructions on Using Program Mode)
To Set the IntelliMute Activation Point Using Program Mode
(See Page 7 For Instructions on Using Program Mode)
In Program mode, go to Set IntelliMute. Press and release the Set/City button to begin setting IntelliMute RPMs. Rev the engine slightly above idle and hold revs steady for two seconds. Press and release either the Select/Dim button to proceed to the next user mode or the Program/Mute button to exit the Program mode.
Tone None Two beeps
Visual Display Set IntelliMute Press SET at desired RPMs. . . None
Voice None Set Engine Revs None
None
Three beeps None
IntelliMute Set!None
IntelliMute Set None
In Program mode, go to IntelliMute Pro.
Tone Two beeps
Visual Display IntelliMute Pro On, then i blinks in the display IntelliMute Pro Off, then i is steady in the display
IntelliMute Pro Off
Voice IntelliMute Pro On
One beep
Setting IntelliMute RRMs
IntelliMute Pro Off
NOTE If the unit is unable to sense usable pulses within three seconds or if you do not set a rev point within 20 seconds of beginning these steps, IntelliMute will indicate an error and automatically turn Off.
Tone One beep One beep
16 English
Set Intel. . .
PressSET. . .
Intelli Mute Set!
IntelliMute Pro On
Intelli Mute Pro On NW ih
Intelli Mute Pro Off NW ih
Nothing Comes Close to a Cobra® 17
IntelliMute Not Set
IntelliMute Off
Visual Display IntelliMute not set Please try again IntelliMute Off
Voice IntelliMute not set Please try again IntelliMute Off
IntelliMu. . . Please tr. . .
Intelli Mute Off
Your Detector
Settings
N NW W SW S
8-Point Compass
Your Detector
Settings
Set/City Button
Compass
Your detector includes an internal 8-point Compass that will continuously display your current direction of travel: N, NE, E, SE, S, SW, W or NW. Calibrating the Compass
NE E SE
Select/Dim Button Program/Mute Button
To Calibrate the Compass Using Program Mode
(See Page 7 For Instructions on Using Program Mode)
In Program mode, go to Set Compass. Press and release the Set/City button to begin setting the compass.
Tone None One (1) beep
Visual Display Set Compass
Voice None
NOTE Before using it for the first time, you must calibrate the compass to provide accurate indications of direction. See page 7 for instructions on using the Program mode to select Set Compass. Calibration allows the compass electronics to measure and store information about the magnetic fields generated by your vehicle. The compass will remain accurately calibrated as long as your detector is mounted in the same place in your vehicle. If you change the location where the unit is mounted or move it to another vehicle, you must recalibrate the compass. The compass temporarily may not provide accurate readings if you are inside a building or enclosure, or are close to a large metal tractor/trailer, truck, or train. Once you are away from such a location, the compass will work correctly again. NOTE When the instructions direct you to drive in two circles, a large parking lot is the most convenient place to do so. It does not matter what direction your vehicle is pointing when you start the circles, which direction you go to make the circles, and it does not have to be exactly two circles. Four three-point turns, two small squares, or any two complete loops will work as well as two circles. It does not matter what size the circles are, if your speed is constant, or how fast you make the circles [but less than two minutes]. Please be careful when making the circles and watch for other traffic.
Drive in 2 Set Compass circles. . . For two seconds followed by direction of travel (N, NE, E, SE, S, SW, W or NW) None Compass Set
Within two minutes, drive your vehicle in a circle twice, then press the Set/City button again.
Three beeps
Press and release either the Select/Dim button to proceed to the next user mode or the Program/Mute button to exit Program mode.
Set Compass
None
None
Calibrate Compass
Compass Set
Direction of Travel
Set Compa. . .
Drive in. . . [. . . ] Make sure the socket of your vehicle's cigarette lighter is clean and free of corrosion. Make sure the power cord's cigarette lighter adapter is firmly seated in your cigarette lighter. (Unscrew the ribbed end cap of the cigarette lighter adapter and examine the fuse. If required, replace it with a 2-amp fuse only. )
This radar detector is covered by one or more of the following U. S. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE COBRA XRS 970
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual COBRA XRS 970 will begin.