User manual COBRA XRS 9545 QUICK START GUIDE

[. . . ] Introduction Intro Important Information and Customer Assistance Operation Customer Warranty Assistance Important Information Federal Laws Governing the Use of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra radar/ laser detector. The Communications Act of 1924 guarantees your right to receive radio Secondary Icons transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action. Operating Instructions Safety Alert Use of this product is not intended to, and does not, ensure that motorists or passengers will not be involved in traffic accidents. [. . . ] desired RPMs Notice n Icons Intro Operation Customer Assistance ih Warranty ih Notice If, for any reason, the unit stops sensing your engine's revs, IntelliMute will indicate an error and automatically turn Off. Intro ondary Icons To Set the IntelliMute Activation Point Press and hold the IntelliMute button for two seconds. Main Icons Tone Two beeps Voice Set Engine Revs Visual Display Press IntelliMute button again at desired RPMs None Operation The rev point you set will be stored in the unit's memory when power is turned Off and recalled each time the power is turned On. NOTE The rev point must be reset if you use your detector in a different vehicle. Notice Customer Assistance Warranty ondary Icons Operation NOTE When initially choosing your IntelliMute activation point, a setting Notice of approximately 300 to 600 RPMs above idle is recommended. Customer Warranty Assistance You can reset the activation point at any time to fit your individual preferences and driving style. Customer Setting the IntelliMute Activation Point Assistance Your detector must be installed in your vehicle. Rev your engine to None the level you wish to set (recommend slightly above idle) and hold revs Intro steady Operation for two seconds. At the desired rev level, press and release the Secondary Icons IntelliMute button. IntelliMute Not Set None Customer Assistance Warranty Three beeps IntelliMute Set IntelliMute Set! Installation Notice Caution CAUTION Do not attempt to set the rev point while driving. Please tr. . . IntelliMute Off Notice NOTE If the unit is unable to sense usable pulses within three seconds or if you do not set a rev point within 20 seconds of beginning these steps, IntelliMute will indicate an error and automatically turn Off. Tone Four beeps Voice IntelliMute Not Set, Please Try Again followed by IntelliMute Off Visual Display IntelliMute not set Please try again IntelliMute Off 11 IntelliMute must be turned On before setting the activation point. Depending on whether the unit is in Tone Alert or Voice Alert mode, you will hear a series of beeps or voice messages as you follow the steps on the next page. Intelli Mute Off One beep 10 English Nothing Comes Close to a Cobra® Your Detector Intro Operation Settings Customer Warranty Your Detector Intro Operation Settings Customer Warranty Assistance IntelliMute Pro Assistance Voice/Tone Setting IntelliMute Pro prevents detection by radar detector detectors (RDDs) such as VG-2, Spectre I and Spectre IV+ when traveling at slower speeds. It is intended for use by experienced users only. eration Customer Secondary Icons Assistance You can set your detector to sound alerts with either a Voice or a Tone. You can change settings by using the Mute button. Secondary Icons When IntelliMute Pro is turned On, and engine RPMs are below the IntelliMute activation point, your detector's radar detection circuits are turned Off to prevent detection by RDDs. Main Icons Warranty In Voice Alert mode, you will first hear several tones, then a voice message announcing the type of signal detected, followed by more tones. The factory setting is Voice Alert mode. Mute Button Press and hold for Notice two seconds tallation Customer Assistance Before IntelliMute Pro can be turned On, you must have turned On and Set the IntelliMute activation point. (See pages 9 through 11. ) Notice CAUTION Operation Customer Warranty When IntelliMute Pro is On, NO Intro radar signals will be detected and Assistance NOWarning will be given at RPMs below the IntelliMute activation point. alerts IntelliMute Button City Button Secondary Press and hold both Icons buttons simultaneously IntelliMute Pro On To Change From Voice Alert to Tone Alert While no signal is being detected, press and hold the Mute button for two seconds. Tone One beep Voice Tone Alert Visual Display None, after Tone blinks in the display Notice Caution ih Notice NOTE The arrow up or down will continue to show that engine RPMs are above or below the user-set value. To Change From Tone Alert Back to Voice Alert While no signal is being detected, press and hold the Mute button for two seconds again. Tone None Voice Voice Alert Visual Display None, after Voice blinks in the display To Turn IntelliMute Pro On While no signal Tone is being detected, press and hold both Two beeps the IntelliMute and City buttons for four seconds. Voice IntelliMute Pro On Visual Display i blinks continuously in the display after IntelliMute Pro On blinks To Turn IntelliMute Pro Off Press and hold both Tone the IntelliMute and One beep City buttons for four seconds. 12 English Voice IntelliMute Pro Off Visual Display None, after IntelliMute Pro Off blinks Nothing Comes Close to a Cobra® 13 Your Detector Intro Operation Settings Customer Warranty Your Detector Intro Operation Settings Customer Warranty Assistance VG-2 and Spectre I & IV+ Alert Settings Assistance Radar Alert Settings (continued) Police use radar detector detectors (RDDs) to spot users of radar detectors. Your detector is able to identify signals from VG-2, Spectre I and Spectre IV+ RDDs and can provide alerts when any of these or similar devices are in use Secondary Icons your vehicle. near Your detector can be spotted by Spectre IV+ RDDs, but is invisible to VG-2 and Spectre I RDDs. You can choose whether you want to be alerted to VG-2 and Spectre I & IV+ RDD signals. The factory setting for VG-2 and Spectre I & IV+ alerts is Off. Notice To Turn K Band On and Off Secondary Icons While no signal is being detected, press and hold both the Mute and City buttons for four seconds. Tone K On = Two beeps K Off = One beep Voice Visual Display K On blinks in the display K Off blinks in the display K On K Off Spectre I & IV+ and VG-2 On Spectre I & IV+ and VG-2 Off Notice To Turn Ku Band* On and Off Spectre & VG2 Spectre & VG2 Off Dim Button Press and hold for four seconds On While no signal is being detected, press and hold the City button for four seconds. Tone Ku On = Two beeps Ku Off = One beep Voice Ku On Ku Off Visual Display Ku On blinks in the display Ku Off blinks in the display To Turn VG-2 and Spectre I & IV+ Alerts On and Off While no signal is being detected, press and hold the Dim button for four seconds. Tone On = Two Beeps Off = One Beep Voice Spectre VG-2 On Spectre VG-2 Off Visual Display Spectre & VG2 On blinks in the display Spectre & VG2 Off blinks in the display Pop Alert The Pop Mode Radar Gun is a single-pulse Doppler radar that is a feature of a K and Ka (Bee III Ka radar gun) band Instant-On radar gun. It uses a single, short-time pulse to measure the target vehicle's speed. The Pop mode receiver senses Pop singles beyond the effective range of Pop radar guns. As the Pop mode receiver is so sensitive, you should limit the use of Pop Detect mode to highway and rural driving. [. . . ] If your unit does not appear to be operating properly, please follow these troubleshooting steps: s s s s Make sure the power cord is properly connected. Make sure the socket of your vehicle's cigarette lighter is clean and free of corrosion. Make sure the power cord's cigarette lighter adapter is firmly seated in your cigarette lighter. (Unscrew the ribbed end cap of the cigarette lighter adapter and examine the fuse. [. . . ]