Detailed instructions for use are in the User's Guide.
[. . . ] THE WARRANTIES GIVEN ABOVE ARE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. CISSELL NEITHER ASSUMES, NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT, ANY OTHER WARRANTY OR LIABILITY IN CONNECTION WITH THE MANUFACTURE, USE OR SALE OF ITS EQUIPMENT OR PARTS. For warranty service, contact the Distributor from whom the Cissell equipment or part was purchased. If the Distributor cannot be reached, contact Cissell.
Page 2
DRAWINGS DIMENSION DRAWINGS
All dimensions are in inches ± 1/4.
Page 3
INSTRUCTIONS FOR STEAM CONNECTIONS FOR PUFF IRONS IMPORTANT: INSTALL STEAM PIPING IN ACCORDANCE WITH ALL LOCAL REGULATIONS AND REQUIREMENTS.
1. [. . . ] If steam is gravity-returned to boiler, omit trap but install check valve in return line near machine. Install union and globe valve to return line and make final pipe connection to return header. CAUTION: Before operating Puff Iron, open globe valves in steam lines and allow Puff Iron to warm up. Under no circumstances should machine be operated until hot.
RECOMMENDATIONS
1. When machine is on the end of a line of equipment, extend headers at least 4 ft. Install globe valve, union, check valve trap and optional by-pass at the end of a line. Insulate steam supply and return line for safety of operator and safety while servicing machine. Repair or replace any worn or defective parts.
Page 4
STEAM PIPING
For wet line conditions, trap w/strainer and check valve should be installed (dotted lines).
12" Minimum Risers
RE TU RN
All piping parts beyond connection points to be furnished by customer.
SU PP LY
1/2" Pipes
CENTRAL AIR VACUUM Globe Valves
1-1/4" Vacuum Connection 3/4" Return Connection 3/4" Elbow 12" Drop
1/2" Supply Connection
SUPPLY RETURN
3/4" x 1/2" Elbow Check Valve Bucket Trap w/Strainer (Thermodynamic Trap and Y-Strainer may be substituted) Page 5
PUFF IRON TABLE ARRANGEMENTS
Drawings show in-line or angle arrangement of one Double Table and one Single Table. 4X, 4C or 4 Sleever for extra working space.
SINGLE TABLE One 15-1/2" SINGLE TABLE. 4C Sleever with 12" extension.
SINGLE TABLE One 15-1/2" SINGLE TABLE. Drawing shows suggested heads on 38" Triple Table.
SPECIFICATIONS PUFF IRON SPECIFICATIONS
Steam Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P155 P158 P159 P167 P161 P166 P219 TU2846 TU4934 P189 Description Back, Single Table Back, Single w/Extension Back, Double Table Back, Triple Table Back, Double w/Extension Back, Triple w/Extension Tr. 1/4"-20 x 1/2" Lockwasher, 1/4" Hex Nut, 1/4-20 17" Corner and Back Ref. P156 P505 Description 12" x 12" Extension Extension w/Brace & Hardware for Single or Triple Extension w/Brace & Hardware for Double Extension Brace for Single & Triple Extension Brace for Double Table
P507 13 14 P483 P484
Page 8
PARTS VACUUM MANIFOLD PARTS
Ref. P252 P523 P257 P284 P253 P271 M263 P256 P276 P277 Description Hose Adapter Vacuum Manifold, Triple Table* Vacuum Manifold, Double Table* Vacuum Manifold, Single Table* Manifold Cap, 1-1/2" Adapter Cap, 3/4" #8 - 3/8" S. M. S. Pipe Clamp "O" Ring Union w/"O" Ring
* Includes Hose Adapter(s)
Page 9
For Egg Heads Only, Use P527 Flow Control Valve
Page 10
ALVES RELATED PARTS SINGLE TABLE - VALVES AND RELATED PARTS
Puff Iron "D" Models without Vacuum
Ref. TU4599 P262 P266 P466 P470 P504 P506 390401246 TU4607 P273 M280 390401013 OP267 P459 P460 P461 P519 390401031 OP267 P115 TU4598 P465 TU2814 C249 TU4934 TU2846 SF49 P228 P132 P98 P126 P36 TU4600 P525 OP297 OP268 P524 P526 P529 Description Steam Pipe, 3/4" x 18" Jacket Flange 90° Fitting, 3/8"P x 1/4"T Disc Valve Assembly Renewable Disc Packing Nipple, 3/8" x 3-1/2" Nipple, 3/4" x 2-1/2" Carriage Bolt, 5/16" - 18 x 3/4" Carriage Bolt, 1/4" - 20 x 1" Nipple, 1/2" x 7" Bushing, 3/4" x 1/2" Cross, 3/4" Bushing, 3/4" x 1/4" Fitting, St. 1/4"P x 1/4"T Straight Upsteam Tube Assembly Nipple, 3/4" x Close Bushing, 3/4" x 1/2" Tee, 3/4" x 3/4" x 3/8" Nipple, 3/4" x 6" Valve Rod Lockwasher, 5/16" Hex Nut, 5/16 - 18 Hex Nut, 1/4 - 20 Lockwasher, 1/4" Yoke Assembly Foot Pedal Support Bar Collar Set Screw, 1/4" - 20 Pedal Wrench Union, 3/4" "L" Shaped Tube Straight Connector, 1/8"P x 1/4"T Reducing El, 1/4"P x 1/8"P 90° Connector, 1/4"P x 1/4"T Insulation Insulation
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
Page 11
For Egg Heads Only, Use P527 Flow Control Valve
Page 12
ALVES RELATED PARTS DOUBLE TABLE - VALVES AND RELATED PARTS
Puff Iron "D" Models without Vacuum
Ref. P266 OP296 TU4599 P262 P466 P470 P504 P506 390401246 TU4607 OP267 P459 P460 P461 390401031 P115 TU4610 TU4600 P273 M280 P266 TU2846 TU4934 TU2814 C249 P519 P465 SF49 P228 P177 P98 P126 P36 P525 OP297 OP268 P524 P526 P529 TU4598 P532
Description Flange Nipple, 1/2" x 5" Steam Pipe, 3/4" x 18" Jacket 90° Fitting, 3/8"P x 1/4"T Disc Valve Assembly Renewable Disc Packing Nipple, 3/8" x 3-1/2" Nipple, 3/4" x 2-1/2" Bushing, 3/4" x 1/2" Cross, 3/4" Bushing, 3/4" x 1/4" Fitting, 1/4"P x 1/4"T Nipple, 3/4" x Close Tee, 3/4" x 3/4" x 3/8" Nipple, 3/4" x 5" Union, 3/4" Carriage Bolt, 5/16" - 18 x 3/4" Carriage Bolt, 1/4" - 20 x 1" Flange Lockwasher, 1/4" Hex Nut, 1/4" - 20 Lockwasher, 5/16" Hex Nut, 1/4" - 20 Straight Upsteam Tube Assembly Valve Rod Yoke Assembly Foot Pedal Support Bar Collar Set Screw, 1/4" - 20 Pedal Wrench "L" Shaped Tube Straight Connector, 1/8"P x 1/4"T Reducing El, 1/4"P x 1/8"P 90° Connector, 1/4"P x 1/4"T Insulation Insulation Nipple, 3/4" x 6" Steam Valve Rod - Used on Vacuum Models Only for Right Side Head
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
Page 13
For Egg Heads Only, Use P527 Flow Control Valve
Page 14
ALVES RELATED PARTS TRIPLE TABLE - VALVES AND RELATED PARTS
Puff Iron "D" Models without Vacuum
Ref. PIF163 PIF162 PIF161 X54 X56 S9 PIF169 PIF204 PIF172 PIF164 PIF167 V12 V345 PIF202 PIF154 Description Swinging Arm Support Upright Support Base Handle End Cork Handle Handle Belt Support Holder Stop Delrin Bushing Spacer Pivot Stud Gland Spring Latch Extension Spring Ref. Description C396 TU2846 P219 S20 AT368 TU4820 RC355 IB143 TU2847 P302 J10 VSB154 P163 P164 TU4934 Crown Nut, 1/4 - 20 Lockwasher, 1/4" Tr. Scw. , 1/4" - 20 x 1/2" #8 - 32 Crown Nut Lockwasher, #8 Cut Washer, #10 Hex Cap Scw. , 1/4" - 28 x 1 - 1/2" Hex Nut, 1/4" - 28 Cut Washer, 1/4" Tr. [. . . ] SG89 OP329 J17 SG38 GSB145 OP268 SGV35 SG25 SG37 SGO43 SG49 SG50 SG90 SGV1 SGC2 TU4604 TU4595 TU2714 J21 V56 OP297 PU8 SU65
Description 1/4" L Shaped Pipe Large Hose Clamp "S" Hook Suspension Spring Small Hose Clamp 90° Reducing Pipe EL 1/4" x 1/8" (2 Req'd) Brass Adapter Hose Gasket 5 Ft. Water Hose Assembly Overhead Water Spray Gun (See Separate Part Sheet) Bracket for Water Spray Gun "J" Bolt 1/4" Tubing 31" Long Valve (See Separate Part Sheet) Condenser (See Separate Part Sheet) 3/4" x 9-3/4" Black Pipe 3/4" x 1/2" x 3/4" Pipe Tee 1/2" Close Nipple 1/4" - 20 x 3/4" Sq. Set Screw 5/16" - 20 Hex Nut 1/4" Tube x 1/8" Pipe Straight Connection w/Nut & Bead 1/4" Bead 1/4" Nut
Page 20
ALVE SERVICE FOR PUFF IRON DISC VALVE
CAUTION: When working on Puff Iron Disc Valve or Heads. . . Do not overtighten pack nut as this will cause packing to bind upon stem and hold valve open. [. . . ]