User manual CHICAGO MOTOCROSS DIRT BIKE STAND

[. . . ] Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. For technical questions or replacement parts, please call 1-800-444-3353. saVe tHis Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. notice is used to address practices not related to personal injury. [. . . ] If unreadable or missing, contact Harbor Freight Tools for a replacement. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. saVe tHese instructions. Motocross bike stand safety Warnings 1. Keep clear of Release Bar and do not leave unattended while supporting load. Page 3 speciFications Weight Capacity 350 lb. Pedal U-Shaped Bracket unpacking When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. · Washer (9); Long Bolt Insert Long Bolt (6) through: · One hole in U-shaped Bracket under Saddle (1); · Bushing (10); · Hole in end of Pedal (3); · Bushing (10); · Other hole in U-shaped Bracket; · Washer (9). Insert Short Bolt (7) through: · Washer (9); · Mounting Bracket (5); · Washer (9); · Remaining hole in Pedal (3); · Washer (9); · Remaining Mounting Bracket (5); · Washer (9). asseMblY read the entire iMportant saFetY inForMation section at the beginning of this manual including all text under subheadings therein before set up or use of this product. note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Make sure rubber end caps are secured into feet of Base (2). Steps 4 and 5 5. Insert remaining Short Bolt (7) through: · Washer (9); · Release Bar (4); · Washer (9); · Remaining hole in Mounting Bracket (5); · Washer (9); Steps 6 and 7 Steps 2 and 3 SKU 66552 For technical questions, please call 1-800-444-3353. Page 4 · Hole in foot on Base (2); · Washer (9); · Remaining hole in second Mounting Bracket (5); · Washer (9). Before using the Bike Stand with a load, test the operation of the Pedal and Release Bar, without any load, following the operating instructions below. r-pin (12) locking pin (11) 4. operating instructions read the entire iMportant saFetY inForMation section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Locate Stand on hard, flat, and level surface able to withstand load without deforming. Center dirt bike over Saddle and secure to saddle with tie-down strap (sold separately) before lifting. Using second person to stabilize load, slowly raise Saddle by depressing Pedal with your foot until Saddle is fully raised. 5. Insert Locking Pin (11) fully through the hole in the saddle and the base to secure the stand in the up position. Using second person to stabilize load, press on Release bar while guiding Pedal up to smoothly lower Saddle. 6. 7. 2. 3. SKU 66552 For technical questions, please call 1-800-444-3353. Page 5 Maintenance and serVicing Procedures not specifically explained in this manual must be performed only by a qualified technician. to preVent serious injurY FroM tool Failure: do not use damaged equipment. if abnormal noise or vibration occurs, have the problem corrected before further use. please read tHe FolloWing careFullY THe MANUFACTUReR AND/OR DISTRIBUTOR HAS PROvIDeD THe PARTS LIST AND ASSeMBLy DIAgRAM IN THIS MANUAL AS A ReFeReNCe TOOL ONLy. [. . . ] To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. [. . . ]