User manual CHICAGO 93861

[. . . ] If any parts are missing or broken, please call Harbor Freight Tools at the number above as soon as possible. SAFETY WARNINGS AND PRECAUTIONS 1. Make sure to wear ANSI approved safety impact eye goggles when installing this Light Kit. Prior to installing this product, make sure to read and understand all instructions and safety precautions as outlined in the (trailer, camper, etc. ) manufacturer's manual onto which the Light Kit will be installed. 3. This Light Kit is NOT waterproof, and will become seriously damaged if submerged in water or other liquids. [. . . ] 9. 10. ASSEMBLY INSTRUCTIONS Vehicle Connection: 1. Note: Connect the Light Kit after the trailer is fully assembled. Connect the BROWN wire of the Color Coded Trunk Harness (5) to the towing vehicle's Tail Light wire. Connect the YELLOW wire of the Color Coded Trunk Harness to the vehicle's Left Hand Stop & Turn light. Connect the GREEN wire of the Color Coded Trunk Harness to the vehicle's Right Hand Stop & Turn light. Make sure to use the BLUE Wire Splitter Connectors to make these connections. Diagram. ) Attach the WHITE GROUND wire to the towing vehicle's frame. Diagram. ) NOTE: If the towing vehicle has rear turn signals separated from its stop lights, you will need to install additional hardware. SPLITTER WIRE CONNECTOR R. H. STOP & TURN (YELLOW) SIDE MARKER (AMBER) RIGHT REAR BROWN SPLITTER WIRE CONNECTOR GREEN 3 REAR MARKERS (RED) REQUIRED FOR TRAILERS OVER 80" WIDE (NOT INCLUDED) GROUND (WHITE) TAIL LICENSE, SIDE MARKER (BROWN) GROUND (WHITE) SPLITTER WIRE CONNECTOR SIDE MARKER (AMBER) YELLOW BROWN LEFT REAR & LICENSE BRACKET SKU 93861 For technical questions, please call 1-800-444-3353 PAGE 2 REV 07k Trailer Light Mounting And Connection: 1. Mount the Stop-Tail-Turn Light (1), marked "L. H. " (with the License Window), on the left rear of the trailer with its side marker to the outside of the trailer. Then, mount the License Plate Bracket (3) with the Stop-Tail-Turn Light. Diagram. ) Mount the Stop-Tail-Turn Light (1), marked "R. H. " (without the License Window), on the right rear of the trailer with its side marker to the outside of the trailer. Diagram. ) Use the Metal Frame Clips included in the Mounting Hardware Package (6) to mount each half of the Split Y-Style Harness (4) down each side of the trailer. Run the YELLOW and BROWN wires down the left side and GREEN and BROWN wires down the right side of the trailer. Diagram. ) Connect the YELLOW and BROWN wires to the left hand Stop-Tail-turn Light (1) with the Wire Nut Connectors included in the Mounting Hardware Package (6). Diagram. ) Connect the GREEN and BROWN wires to the right hand Stop-Tail-turn Light (1) with the Wire Nut Connectors included in the Mounting Hardware Package (6). Diagram. ) Attach the WHITE GROUND wire to the trailer tongue or frame. Diagram. ) Mount the two Marker Clearance Lights (2) in the areas shown in the illustration. Connect each wire from the Marker Clearance Lights to the BROWN wire on each half of the Split Y-Style Harness (4). Diagram. ) Connect the Split Y-Style Harness (4) Plug to the Color Coded Trunk Harness (5) Plug. [. . . ] Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. [. . . ]