User manual CATEYE STRADA WIRELESS

[. . . ] When using the computer installed on the bracket, change the MODE by pressing on the three dots below the screen. Pressing hard on other areas can result in malfunction or damage to the computer. When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol. LCD screen may be distorted when viewed through polarized sunglass lenses. 1 Bracket band 2 Bracket 3 Speed sensor 4 Magnet 5 Sensor rubber pad 6 Bracket rubber pad 7 Nylon ties (x2) Install the sensor and magnet A The distance between the computer and the sensor must not exceed the transmission range of 70 cm. [. . . ] With the riders weight on the bike, roll the wheel one tire revolution in a straight line and mark the ground when the valve stem is perpendicular to the ground again. This is the most accurate wheel calibration number. 4 Remove/install the computer Click Holding the unit Cut Push outward Caution: Round off the cut edge of the bracket band to prevent injury. * After installation, rotate the front wheel gently to check that the speed is displayed on the computer. If the speed is not displayed, check that conditions A , B , and C , above, have been done appropriately. L mm CC-RD300W Operating the computer [Measuring screen] Troubleshooting MODE does not work when the computer is mounted on its bracket. Wash off the bracket with water to get rid of any dirt, and to ensure that the computer slides in and out smoothly. (The speed is not displayed. ) (Spin the front wheel, bringing the computer closer to the sensor. If the icon now flashes, this indicates that the computer and sensor are too far apart or that the battery is low. ) Is the clearance between the sensor and magnet too great?(The distance must not exceed 70 cm. ) Install the sensor closer to the computer. In the case of the computer, after replacing the battery, re-start the computer according to the "Preparing the computer", above. Then reinitialize the computer referring to "Preparing the computer". Reinitialize the computer referring to "Preparing the computer". Tm Elapsed Time 0:00'00" - 9:59'59" Pace arrow Indicates whether the current speed is faster ( ) or slower ( ) than the average speed. Dst Trip Distance 0. 00 - 999. 99 km [mile] Current speed 0. 0(4. 0) - 105. 9 km [0. 0(3. 0) - 65. 9 mph] Dst2 Trip Distance-2 0. 00 - 999. 99 / 1000. 0 - 9999. 9 km [mile] Selected Mode Starting/Stopping measurement Measurements occur automatically when the bicycle is in use. During measurement, or flashes. Av Average Speed*2 0. 0 - 105. 9 km/h [0. 0 - 65. 9 mph] MODE *1 Switching computer function Pressing MODE switches function, in order, as shown on the left. Mx Maximum Speed 0. 0(4. 0) - 105. 9 km/h [0. 0(3. 0) - 65. 9 mph] Resetting data To reset measurement data, display any data other than for Dst-2 and then press and hold MODE. The total distance is never reset. Odo Total Distance 0. 0 - 9999. 9 / 10000 - 99999 km [mile] Specification Battery . . . . . . . . . . . . . . . . . Computer : Lithium battery (CR2032) x 1 Sensor : Lithium battery (CR2032) x 1 Battery life . . . . . . . . . . . 1 years (If the computer is used for 1 hour/day; the battery life will vary depending on the conditions of use. ) Sensor : Unit Total Distance reaches about 10, 000 km (6, 250 mile) * This is the average figure of being used under 20 °C temperature and the distance between the computer and the sensor is 65 cm. 4-bite, 1-chip microcomputer (Crystal controlled oscillator) Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0100 mm - 3999 mm (Default figure A: 2096 mm, B: 2096 mm) Working temperature . . . . . . . . . . . . . . . 32 °F - 104 °F (0 °C - 40 °C) (This product will not function appropriately when exceeding the Working Temperature range. Slow response or black LCD at lower or higher temperature may happen respectively. ) Dimensions/weight . . . . . . . . . . . . . . . . . . . 1-53/64" x 1-7/32" x 5/8" (46. 5 x 31 x 16 mm) / 0. 78 oz (22 g) * The factory-loaded battery life might be shorter than the above-mentioned specification. * The specifications and design are subject to change without notice. Clock 0:00 - 23:59 or 1:00 - 12:59 *1 With the computer installed on the bracket, press on the three raised dots on the face of the computer. [. . . ] For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn: CATEYE Customer Service Section Service & Research Address for USA CATEYE Service and Research Center 1705 14th St. 115 Boulder, CO 80302 Phone: 303. 443. 4595 Toll Free: 800. 5CATEYE Fax: 303. 473. 0006 E-mail: service@cateye. com URL: http://www. cateye. com Setting * After changing, be sure to press MENU to register the change (by setting. pressing & * If the menu screen is not touched for a minute, the MODE holding) Measuring screen reappears without data changes. Wheel selection . . . . . [. . . ]