User manual CATEYE STRADA CADENCE

[. . . ] When using the computer installed on the bracket, change the MODE by pressing on the three dots below the screen. Pressing hard on other areas can result in malfunction or damage to the computer. If you do, the contact points will conduct electricity, discharging the battery. When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol. [. . . ] (Touch a metal item against two contact points of The contacts to be shortthe computer several times to create a short circuit while observing the display. If a circuited intermittently are numeric value appears, this signifies that the computer is functioning normally. ) located on the back. Adjust the positions of the magnet and sensor. Tm Elapsed Time 0:00'00" - 9:59'59" Pace arrow Indicates whether the current speed is faster ( ) or slower ( ) than the average speed. C Cadence 0(20) - 299 rpm Current speed 0. 0(4. 0) - 200. 0 km [0. 0(3. 0) - 125. 0 mph] Dst Trip Distance 0. 00 - 999. 99 km [mile] Selected Mode Speed Cadence Dst2 Trip Distance-2 0. 00 - 999. 99 / 1000. 0 - 9999. 9 km [mile] MODE Starting/Stopping measurement Measurements occur automatically when the bicycle is in use. During measurement, or flashes. *1 Av Average Speed*2 0. 0 - 200. 0 km/h [0. 0 - 125. 0 mph] Switching computer function Pressing MODE switches function, in order, as shown on the left. Mx Maximum Speed 0. 0(4. 0) - 200. 0 km/h [0. 0(3. 0) - 125. 0 mph] Resetting data To reset measurement data, display any data other than for Dst-2 and then press and hold MODE. The total distance is never reset. Is there any foreign matter (which would prevent a clean contact) on the contact points of the computer and/or bracket?Even with a normal appearance, it may be that a wire cable could be broken internally. Then reinitialize the computer referring to "Preparing the computer". Reinitialize the computer referring to "Preparing the computer". Specification Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lithium battery (CR1620) x 1 Battery life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 years (Using the battery one hour a day; the battery life will vary with the conditions of use. ) Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-bite, 1-chip microcomputer (Crystal controlled oscillator) Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0100 mm - 3999 mm (Default figure A: 2096 mm, B: 2096 mm) Working temperature . . . . . . . . . . . . . . . 32 °F - 104 °F (0 °C - 40 °C) (This product will not function appropriately when exceeding the Working Temperature range. Slow response or black LCD at lower or higher temperature may happen respectively. ) Dimensions/weight . . . . . . . . . . . . . . . . . . . 1-53/64" x 1-7/32" x 19/32" (46. 5 x 31 x 15 mm) / 0. 63 oz (18 g) * The factory-loaded battery life might be shorter than the above-mentioned specification. * The specifications and design are subject to change without notice. Standard Parts Odo Total Distance 0. 0 - 9999. 9 / 10000 - 99999 km [mile] Clock 0:00 - 23:59 or 1:00 - 12:59 *1 With the computer installed on the bracket, press on the three raised dots on the face of the computer. *2 If Tm exceeds approximately 27 hours or DST exceeds 999. 99 km, . E (Error) is displayed as the average speed. Reset data. Power-saving function If the computer has not received any signal for an hour, powersaving mode will activate and only the clock will be displayed. [. . . ] Pressing MODE increases the value, and pressing and holding MODE moves to the next digit. This reading will later allow you to enter the total distance manually. Pressing MODE increases the value, and pressing and holding MODE moves to the next digit. Pressing MODE toggles between Maintenance To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and wipe it off with a dry cloth. Replacing the battery If the display appears faded, replace the battery. [. . . ]