User manual CATEYE ABS-10

[. . . ] Rechargeable Head Lamp ABS-10 Instruction Manual Advanced Battery System SINGLE Ni-MH 6v Lamp Unit E Pat and Design Pat. ABS10W-020830 066640034 1 READ ALL INSTRUCTIONS BEFORE FIRST USE Thank you for purchasing the CAT EYE ABS Advanced Battery System, a unique 6 volt rechargeable head lamp series. Before operating, thoroughly familiarize yourself with this manual so that you understand the light's safe and correct operation. [. . . ] Take precautions against such a situation and prepare a spare light or spare battery packs. · Long periods of non-use will lower the voltage of the battery and will naturally self discharge. · Overdischarge (leaving the light on after the power is completely gone) shortens the performance life of the battery. · If the lamp body or parts become dirty with mud, etc. , clean with a soft cloth which is moistened with mild soap. Never apply paint thinner, benzine or alcohol; damage will result. CONTENTS The ABS-10 are the combined system of the following parts. Make sure that your package includes all the parts. Battery Belt (L/S) Cable Cover Switch Unit Holder Mounting Bolts (L x 2, S x 2) Holder HOW TO SETUP Bracket (H-32) RECHARGING INSTRUCTIONS Attach the bracket (H-32) to the handlebar. Attach the switch unit onto the handlebar where it will not hinder the braking and shifting operation. · Recharge after thorough discharge. (in order to prevent memory after effect) · Use exclusive charger. CLICK! Lever Switch Unit Charge indicator Rubber Pad Quick lever screw CLICK! Velcro CLICK! or Connecting Battery Pack and Cord Choose your favorite location to attach the battery packs. When attaching to bottle cage Attach the holder onto the down tube using the holder mounting bolts (L or S). Holder mounting bolts Holder Battery Pack Attention: Fix the battery pack securely with the hold-down straps. For safety's sake, also use the battery belts (velcro straps) to secure the batteries. · Recharge only when battery power has completely diminished. Standard Charging Time · Fully charged batteries that yields no power hours means battery life is dead. The home power outlet 8-10 Bulb HOW TO REPLACE THE BULB Disassemble the lamp unit as illustrated. · Use only the CAT EYE 6V halogen bulb. 1 Fit inside Holder Strap 2 Wind stape When attaching to frame Fix the battery pack firmly to the frame, using the battery belts. Cut the battery pad and fit it between the top tube and the battery, so that the battery will not move when riding. Battery Pad How to run the battery belt through the slot Frame Velcro Cable Cover Cable Battery Belt Battery pack Ring Top Tube Attention: If the cable is not covered by cable housing, use the included cable cover to prevent direct contact between the cable and the belts. (Cut the cable cover to the suitable length. ) SAFETY SYSTEM (AUTO-RESET FUSE) When an electrical surge or malfunction occurs in the circuit or the temperature of the battery rises, the fuse blows due to its safety system and the circuit will be closed. After leaving it for a while, the fuse will automatically recover. Note: If the fuse continues to blow, or if the fuse does not recover, call the appropriate service center for assistance. SPECIFICATIONS Bulb: 6V Halogen wide bulb (10W) Battery pack: Hi Ni-MH battery 6V 3000mAh Battery charger: Hi Ni-MH charger CHR-3005 Standard charging time: 8-10 hours Temperature range: Charging: 0°C - 40°C Operating: ­15°C - 45°C Recharge/discharge number of times: about 500 times (until the rated capacity drops to 50%) * The specifications and design are subject to change without notice. Connecting Cord Connect the battery pack, joint cord and the switch unit as illustrated. Attention: Battery Pack Cord belt · Secure the cord along the frame with the cord Jack belt, so that it will not hinder riding. [. . . ] Do not mix batteries that are in different states of charge. #533-8670 ABS Switch Unit HOW TO SWITCH ON/OFF Release Quick release lever #533-8784 ABS Battery Belt The switch unit controls the operation of the lamps. Run Time: 1. 5 hrs Note: The run time shown here is the calculated figure. · To adjust the angle of the lamp unit, use the quick lever. #533-8783 ABS Joint Cord ABS Battery Charger #533-8676 for U. S. A & Canada #533-8674 for Europe #533-8675 for AS #533-8672 for UK #533-8785 ABS Double Holder #534-0582 10W 6V ABS Wide Bulb #534-0589 ABS Lamp Body [. . . ]