User manual CAT EYE CC-FR7CL CORDLESS 7

[. . . ] Paint thinner, benzine, alcohol or other chemicals may damage the surface. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CYCLOCOMPUTER CC-FR7CL E OWNER'S MANUAL Cordless 7 Installation of Computer: 3 Magnet Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Cat Eye Co. , Ltd. CCMFR7CL-021210 Printed in Japan 066600165 1 About cordless system The sensor picks up the wheel revolution signal and transmits the signal to the computer; the computer calculates and displays the data on the screen. [. . . ] · Press the SET button when complete. SET MODE increase the figure MODE move to the next digit Sensor Base (fig. C) 2 Sensor Base ST. /STOP NOTE: When the wheel rotates, the magnet MUST line up with the mark on the sensor. ALSO NOTE: Magnet must pass within 5 mm of the sensor--if not, it will not trip the sensor as it passes, and the computer will not register speed. Adjusting the sensor position higher or lower on the fork leg or by rotating the sensor on the fork mount may be required to achieve proper distance to the wheel magnet. Less than 5mm SET 3 2 Magnet's center Marking line 3 2 Spin · · · · · · Wheel circumference number is shown. Press SET button when finished. increase the figure MODE 3 4 Test by spinning the front wheel. If not, make sure 1) the magnet is close enough to sensor (within 5 mm); and 2) the sensor is close enough to computer head (within 70 cm) and 3) nothing is obstructing the line of sight between the sensor and the computer head. decrease the figure ST. /STOP OK Sensor Pulse Indicator SET Setup Completed (To Tm) In this state Auto Time is ON. Operation of Computer Speed Scale Indicator - "mph" or "km/h" on main display flashes when computer is measuring speed. Display Modes - Press MODE button to shift lower display from one mode to the next. The display modes change from Elapsed Time (Tm), to Average Speed (Av), to Maximum Speed (Mx), to Total Odometer (Odo), to Trip Distance (Dst). CLOCK TIME - Hold MODE button for 2 seconds to display Clock Time (this works in any of the display modes). [To set correct Clock Time, press SET button when Clock Time is showing in lower display. Use MODE button to increase the digit number, and press SET to change to next digit. - When this is activated, the computer will autoAUTO TIME matically start and stop measuring Elapsed Time (Tm), Average Speed (Av), and Trip Distance (Dst), as soon as the bike starts icon shows in main moving. To turn feature on or off, press SET button while lower display is in Elapsed Time (Tm), Average Speed (Av), or Trip Distance (Dst) activated. For best results, operate the computer with MANUAL MODE - Press the START/STOP button to start the Elapsed Time (Tm), Average Speed (Av) and Trip Distance (Dst) is not activated. [. . . ] 1 year (in the case of being used for 1 hour every day) Sensor: until Total Distance reaches about 10, 000km (6, 250mile) *This is the average figure of being used under 20°C temperature and the dis tance between the computer and the sensor is 65cm. Controller -------------------------- 4-bit 1-chip microcomputer (crystal controlled oscillator) Display ----------------------------- Liquid crystal display Sensor ------------------------------ No contact magnetic sensor Wheel Circumference Range ---- 10mm-2999mm (default figure: A: 2095mm, B: 2050mm) Working Temperature ------------ 0°C - 40°C (32°F - 104°F) Dimension/Weight ---------------- 1-19/32 x 2-7/32 x 27/32" (40 x 56. 5 x 21mm) / 1. 06oz (30g) * The factory-loaded battery life might be shorter than the above-mentioned specification. * The specifications and design are subject to change without notice. Limited Warranty 2-year warranty for computer/sensor only (excluding parts and batteries) If trouble or damage occurs during normal use, the product will be repaired or replaced free of charge. [. . . ]