User manual CASABLANCA FAN COMPAGNY STEALTH

[. . . ] 14 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual completely and carefully. CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure. BEFORE YOU START · All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical codes. The National Electric Code requires proper grounding as a precaution against electrical shock. · This fan is designed to be installed on an existing electrical outlet box. [. . . ] To lower the brightness, turn the lights off, then press and hold the button until the desired brightness level is reached. When the light is on, you may increase the brightness level by pressing and holding the button until the desired level is reached, then release it. LIGHT CONTROL ON - OFF: R A momentary press of the LIGHT button CHANGE BRIGHTNESS: PRESS AND HOLD LIGHT BUTTON LONGER THAN ONE SECOND AUTOMATIC DEMONSTRATION PROGRAM Programmed into every Inteli-Touch Series fan is an Automatic Demonstration Program. It can be used to fully demonstrate and test the operation of the fan. Immediately operate the buttons in the following sequence: FAN - LIGHT FAN - LIGHT FAN A multi-tone signal will verify the start of the test program which proceeds as follows: · Lights slowly increase to full intensity. · Fan turns off with audio tones (blades coast for a short time). It will continue to repeat until the is turned off for more than three seconds, cancelling the program. + + + + 8 R INTELI·TOUCH OPERATION o LIGHT-MINDER® PROGRAM The Light-Minder program automatically turns OFF the fan mounted lights after two hours. Immediately operate the buttons in the following sequence: + + + 4. The fan and light will operate normally using the buttons to turn them on and off. But, if the lights are left on, they will automatically shut off after two hours. cancel the Light-Minder Program, turn the INTELI·TOUCH OPERATION o SAFE-EXIT® PROGRAM The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off, enabling you to exit your home before the lights go out. Immediately operate the buttons in the following sequence: + + + After you hear the confirming audio tones from the fan - immediately press 4. After a total of thirty seconds has elapsed, the lights will be off completely. cancel the Safe-Exit Program, turn the Note: Both Light-Minder and Safe-Exit programs can run at the same time, however the dimmer cannot be used, the light may only be turned ON/OFF. INTELI·TOUCH OPERATION o HOME-SAFE® PROGRAM The Home-Safe Program makes an unoccupied home appear occupied by turning the lights on and off at random times. Immediately operate the buttons in the following sequence: + + + 4. The lights will now be automatically cycled on and off in a controlled sequence as follows: On 1 hour, off 1 /2 hour, on 2 hours, off 1 hour, on 1/2 hour then off 2 hours. This seven hour pattern will repeat continuously so that a different pattern of lighting is seen each day of the week. To cancel the Home-Safe Program, turn the off for three seconds. INTELI·TOUCH OPERATION o FAN-MINDERTM PROGRAM The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the speed of the fan each two-hour interval to compensate for the cooling night air. Immediately operate the buttons in the following sequence: + + + 4. A timer is now initiated and the fan will reduce one speed for each two-hour interval. You may increase the fan speed by pressing and holding the button until the desired speed is reached, then release it. The fan will again reduce one speed for each 2 hour interval. 9 COMFORT·TOUCH o W-21 MOUNTING PARTS WALL BRACKET ANCHOR (4) `AAA' ALKALINE BATTERY (3) R REMOTE CONTROL W-21 REMOTE CONTROL WALL BRACKET WALL BRACKET SCREW (4) COMFORT·TOUCH o W-21 WALL BRACKET INSTALLATION Installation of Remote Control The wall mounting bracket for the remote control should be located in a position that is approximately eye level. [. . . ] These will Be sure to turn power to the fan OFF at the wall switch or circuit damage the finish. Painted and high-gloss blades may be cleaned breaker before changing light bulbs. Blades: Wood finish blades should be cleaned with a furniture pol- wattage of lighting. Occasionally, a light coat of furniture polish may be Exceeding the rated maximum allowable wattage for the fan will burn out the fan electronics module and void the warranty. [. . . ]