User manual CASABLANCA FAN COMPAGNY LEGRANDE

[. . . ] · The fan must be supplied with 3 independent 120V AC supply wires to provide power for the fan, the light, and neutral. For best performance and for your warranty to be valid, use only genuine Casablanca blades, light fixtures, and accessories. SAFE USE · The blades in each pack are matched for equal weight to assure smooth fan operation. If more than one fan is being installed, be careful not to mix blades from different cartons. · Inspect the contents of your carton for possible shipping or handling damage and report any such damage directly to your authorized Casablanca dealer. [. . . ] Securely tighten the allen set screw with the provided allen wrench to ensure safe operation of your fan. CAUTION: Failure to fully lock in the downrod before securely tightening the allen set screw may cause the fan to fall during normal operation! ALLEN SET SCREW MOTOR COUPLING TAPERED THREAD MOTOR WIRES GROUND WIRE DOWNROD & BALL ASSEMBLY GETTING STARTED Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box must be installed and wired. Warning: To reduce the risk of fire, electrical shock, or personal injury, mount to outlet box marked acceptable for ceiling fan support using the mounting hardware provided with the outlet box. Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure that it is marked `Approved for ceiling fan mounting'. NOTE: The fan weight is 23 pounds. 3 CEILING HARDWARE ADDITIONAL HARDWARE 2 1/4 x 8-32 ROUND HEAD SCREWS (2) 1 x 8-32 ROUND HEAD SCREWS (2) FLAT WASHER (2) CROSSBAR MOUNTING BRACKET WIRE NUT (4) CROSSBAR MOUNTING BRACKET INSTALLATION Proceed with installation as follows: Step 1. Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole. Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet box. Tighten the screws firmly by hand only, being careful not to bend the bracket by over tightening. CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket. CEILING FAN APPROVED WIRING BOX CEILING WIRING CROSSBAR MOUNTING BRACKET RIDGE SIDE DOWN FLAT WASHER GREEN GROUND WIRE APPROVED OUTLET BOX HARDWARE CANOPY HARDWARE CANOPY SCREW (4) CANOPY HATCH CANOPY LOCK WASHER (4) CANOPY 4 CANOPY INSTALLATION Step 2. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4 long canopy screws and canopy lock washers. Note: On sloped ceilings, align the canopy opening towards the top or room peak. CROSSBAR MOUNTING BRACKET CANOPY CANOPY LOCK WASHER CANOPY SCREW HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Rotate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening. BALL NOTE: The fan weight is 23 pounds. SLOT PIN CANOPY ELECTRICAL CONNECTIONS Step 4a. Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut. Wiring Connections · GREEN leads from mounting plate and fan to GROUND conductor of power source. · WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box. · BLACK power wire from fan to BLACK power wire in ceiling outlet box. Secure with wire nut. WIRE NUT 2 BLACK WIRES 2 WHITE WIRES 3 GREEN WIRES 5 CANOPY HATCH INSTALLATION Step 5. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Straighten the fan, then check to ensure that there is no movement between the canopy and ceiling or Hang-Tru ball and top support shaft. CANOPY HATCH LOCK WASHER CANOPY SCREW TILT THE FAN TO INSTALL LAST CANOPY SCREW Note: Write down the Serial Number and the model number for future reference. BLADE HARDWARE BLADE SCREW BLADE WASHER BLADE HOLDER BLADE ATTACH BLADE HOLDERS Step 8. Attach the blades to the blade holders by aligning the screw holes of the holder with the holes of the blade. [. . . ] -Downrod is loosely attached to downrod base: Make sure that all screws are securely tightened. -Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s). Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or have fallen off the wire splices. -Tighten blade holders to flywheel (or direct drive motor)/and blade to bladeholder screws. [. . . ]