User manual CASABLANCA FAN COMPAGNY LANAI

[. . . ] For best performance and for your warranty to be valid, use only genuine Casablanca blades, light fixtures, and accessories. SAFE USE · The blades in each pack are matched for equal weight to assure smooth fan operation. If more than one fan is being installed, be careful not to mix blades from different cartons. · Inspect the contents of your carton for possible shipping or handling damage and report any such damage directly to your authorized Casablanca dealer. · It is always a good idea to have an assistant to help with the installation. [. . . ] This is the maximum slope that will allow the fan to hang straight down. It is OK to install your fan. Calculation of 32° Use the tear-off Ceiling Angle Template card inserted in the back of this manual, it provides you with a simple `go' or `no-go' for installing your fan on a sloped ceiling. EXAMPLE 3 This slope is more than 32°. Contact your local Authorized Casablanca Dealer in regards to purchasing a "Slope Ceiling Adaptor. " 2 LANAI PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. PERMA·LOCKTM HARDWARE ALLEN SET SCREW 1 /4-20 x 1/4" (PRE-INSTALLED) 3mm ALLEN WRENCH DOWNROD GASKET DOWNROD & BALL ASSEMBLY DOWNROD GASKET PREPARATION Step A. Slide the downrod gasket onto the downrod as shown, pushing the gasket so that it is snug with the ball of the downrod. FAN PREPARATION IMPORTANT SAFETY INFORMATION! BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN, INSTALL THE THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY GROUND WIRE MOTOR WIRES Prepare for fan installation as follows: Step B. Route the wires from the motor through the Perma·LockTM downrod and ball assembly. Tip: The downrod has a tapered thread that is designed to lock completely when correctly installed. Using the provided allen wrench, loosen the set screw several turns to allow installation of the downrod. Thread the downrod into the motor coupling until it stops turning, this will take at least four and a half full turns. Securely tighten the set screw with the provided allen wrench to ensure safe operation of your fan. CAUTION: Failure to fully lock in the downrod before securely tightening the allen set screw may cause the fan to separate from the downrod during normal operation! ALLEN SET SCREW TAPERED THREAD DOWNROD & BALL ASSEMBLY DOWNROD GASKET MOTOR COUPLING DOWNROD GASKET PREPARATION Step E. Slide the downrod gasket down so that it fits snugly against the motor casing as shown. 3 LANAI CEILING HARDWARE ADDITIONAL HARDWARE 21/4 x 8-32 ROUNDED HEAD SCREW (2) 1 x 8-32 ROUNDED FLAT WASHER (2) HEAD SCREW (2) HANGING PLATE CROSSBAR MOUNTING BRACKET CANOPY GASKET WIRE NUT (4) GETTING STARTED Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box must be installed and wired. Warning: To reduce the risk of fire, electrical shock, or personal injury, mount to outlet box marked acceptable for ceiling fan support using the mounting hardware provided with the outlet box. Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure that it is marked `Approved for ceiling fan mounting'. If it is not, a new box must be installed. CANOPY GASKET PREPARATION Step 1. Make sure that the four holes of the hanging plate align with the four indentations on the inside of the gasket and that the two mounting bracket screw holes align with the two pierced marks in the canopy gasket CANOPY GASKET MOUNTING BRACKET SCREW HOLE HANGING PLATE CROSSBAR MOUNTING BRACKET INSTALLATION Proceed with installation as follows: Step 2. Route the wires from the ceiling outlet box through the center hole of the canopy gasket and hanging plate and then the crossbar mounting bracket center hole. Push the mounting hardware included with the outlet box through the pierced marks in the rubber canopy gasket so that they align with the threaded holes of the ceiling fan approved outlet box. Using the screwdriver, tighten the screws firmly by hand only, being careful not to bend the bracket by over tightening. CEILING FAN APPROVED OUTLET BOX CEILING WIRING CANOPY GASKET & HANGING PLATE CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket. CROSSBAR MOUNTING BRACKET FLAT WASHER RIDGE SIDE DOWN GREEN GROUND WIRE OUTLET BOX MOUNTING HARDWARE 4 LANAI CANOPY HARDWARE CANOPY SCREW (4) CANOPY HATCH CANOPY CANOPY LOCK WASHER (4) CANOPY INSTALLATION Step 3. Thread the wires from the ceiling through the opening in the canopy gasket. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4 long canopy screws and canopy lock washers. [. . . ] Changing Light Bulbs Be sure to turn power to the fan OFF at the wall switch or circuit breaker before changing light bulbs. Exceeding the rated maximum allowable wattage for the fan will burn out the fan electronics module and void the warranty. BREAK-IN PERIOD DOES NOT RUN ON LOW SPEED Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making sure the power is turned off during this inspection. Check the screws holding the blade holders to the flywheel (or direct drive motor). [. . . ]