User manual CASABLANCA FAN COMPAGNY GENERAL

[. . . ] 5 OUTSIDE USA (EXCLUDING MODELS ENDING IN `E') FAN INSTALLATION . 23 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual completely and carefully. CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure. BEFORE YOU START · All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical codes. The National Electric Code requires proper grounding as a precaution against electrical shock. [. . . ] The fan speed is now in memory and will automatically come on at the same speed each time the button is used. To maintain this level of speed, turn the fan on by pressing less than one second. To lower speed, turn fan off, then on by pressing and holding the button until the desired speed is reached. When the fan is on, you may increase the speed by button until the desired speed is reached, pressing and holding the then release it. FAN CONTROL ON - OFF R A momentary press of the FAN button TO CHANGE SPEED Press and hold FAN button longer than one second INTELI·TOUCH OPERATION o REVERSING AIRFLOW The direction of airflow can be changed from downward to upward or from upward to downward. Note: A four-toned signal indicates the command was accepted by the fan. A few seconds later the fan will slow to a stop and then reverse direction. INTELI·TOUCH OPERATION o LIGHT button for less To turn the lights off and on, press and release the than one second. After one second the lights come on at their lowest level and gradually become brighter. The brightness level is now in the fan memory and will automatically come on at the same brightness the next time the button is used. To maintain this level of brightness, press the button for less than one second. To lower the brightness, turn the lights off, then press and hold the button until the desired brightness level is reached. When the light is on, you may increase the brightness level by pressing and holding the button until the desired level is reached, then release it. LIGHT CONTROL ON - OFF A momentary press of the LIGHT button TO CHANGE BRIGHTNESS R PRESS AND HOLD LIGHT BUTTON LONGER THAN ONE SECOND AUTOMATIC DEMONSTRATION PROGRAM Programmed into every Inteli-Touch Series fan is an Automatic Demonstration Program. It can be used to fully demonstrate and test the operation of the fan. Immediately operate the buttons in the following sequence: FAN - LIGHT FAN - LIGHT FAN A multi-tone signal will verify the start of the test program which proceeds as follows: · Lights slowly increase to full intensity. · Fan turns off with audio tones (blades coast for a short time). It will continue to repeat until the is turned off for more than three seconds, cancelling the program. + + + + 15 R INTELI·TOUCH OPERATION o LIGHT-MINDER® PROGRAM The Light-Minder program automatically turns OFF the fan mounted lights after two hours. Immediately operate the buttons in the following sequence: + + + 4. The fan and light will operate normally using the buttons to turn them on and off. But, if the lights are left on, they will automatically shut off after two hours. To cancel the Light-Minder Program, turn the off for three seconds. INTELI·TOUCH OPERATION o SAFE-EXIT® PROGRAM The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off, enabling you to exit your home before the lights go out. Immediately operate the buttons in the following sequence: + + + After you hear the confirming audio tones from the fan - immediately press 4. After a total of thirty seconds has elapsed, the lights will be off completely. Note: Both Light-Minder and Safe-Exit programs can run at the same time, however the dimmer cannot be used, the light may only be turned ON/OFF. INTELI·TOUCH OPERATION o HOME-SAFE® PROGRAM The Home-Safe Program makes an unoccupied home appear occupied by turning the lights on and off at random times. [. . . ] FAN OR LIGHTS APPEAR TO OPERATE BY THEMSELVES (CHANGING SPEED OR INTENSITY), WALL CONTROL OPERATION IS INTERMITTENT: Check AC supply for irregularities, (noise spikes, fluctuations, or failure); or circuit board assembly. 23 PROBLEM PROBLEM FAN WILL NOT START VERSA·TOUCH POSSIBLE REMEDIES POSSIBLE REMEDIES. . FAN WOBBLES OR SHAKES EXCESSIVELY FAN NOISY DURING OPERATION DOES NOT RUN ON LOW SPEED BATTERY LIFE Not using Alkaline batteries: Replace with Alkaline batteries. SEEMS SHORT LIGHT O. K. , NO FAN: Pin connectors are not making good contact, check 9 pin connector under top cover. FAN AND LIGHT ON FULL, NO CONTROL; Defective receiver; Replace Receiver. FAN OPERATES ONLY WHEN TRANSMITTER IS CLOSED: Check antenna wire is not touching metal plate. [. . . ]