User manual CASABLANCA FAN COMPAGNY FOURSEAS3HUG

[. . . ] For best performance and for your warranty to be valid, use only genuine Casablanca blades, light fixtures, and accessories. SAFE USE · The blades in each pack are matched for equal weight to assure smooth fan operation. If more than one fan is being installed, be careful not to mix blades from different cartons. · Inspect the contents of your carton for possible shipping or handling damage and report any such damage directly to your authorized Casablanca dealer. · It is always a good idea to have an assistant to help with the installation. [. . . ] NOTE: The fan weight is 17 pounds. TIP: The packing styrofoam makes a handy work bench. Remove the bottom foam from the box. 2 FOUR SEASONSTM III HUGGER SWITCH HOUSING INSTALLATION Step 1. Hold the switch housing close to the fan and connect the motor plug to the switch housing socket. The connectors are keyed to ensure correct alignment during installation - Do not force!Remove the three mounting screws from the switch housing plate ready for the next step. SWITCH HOUSING MOTOR CONNECTOR (PLUG) MOUNTING SCREW (3) SWITCH HOUSING CONNECTOR (SOCKET) SWITCH HOUSING PLATE SWITCH HOUSING INSTALLATION Step 3. Position the switch housing assembly on the switch housing plate and align the holes in the switch housing with the holes in the plate. Secure the switch housing assembly by reinstalling the three screws removed in the previous step. CAUTION!Do not pinch wires between the switch housing assembly and the plate. MOUNTING SCREW (3) 3 FOUR SEASONSTM III HUGGER INSTALLING THE MOUNTING PLATE Step 4. Carefully feed the ceiling wires through the center hole of the mounting plate then securely attach the mounting plate to the outlet box using the two 8-32 round head screws with star washers supplied. CAUTION: To reduce the risk of personal injury use only the two steel screws (with locking star washers) provided with the fan for mounting to the ouutlet box. Check that the mounting plate is seated firmly against the ceiling and that none of the ceiling wires have been pinched by the plate. If the mounting plate and/or junction box are not securely attached, the fan could wobble or fall. MOUNTING PLATE SCREW AND STAR WASHER CEILING OUTLET BOX CEILING WIRING MOUNTING PLATE REMOVE MOUNTING PLATE NUTS AND WASHERS Step 6. Remove the four nuts and washers from the mounting plate and set aside for use in Step 12. INSTALL STEEL BUSHINGS Step 7. Prepare the motor for installation by attaching the steel bushings into the rubber bushings so that their top surfaces are flush. STEEL BUSHINGS 4 FOUR SEASONSTM III HUGGER HANGING THE FAN TEMPORARILY Step 8. Use the hanging slot of the mounting bracket to hang the fan on the hook of the mounting plate. This will help you in making the electrical connections. WIRING PRELIMINARIES Step 9. To avoid possible electric shock, be sure electricity is turned off at the main fuse box or breaker before wiring. CAUTION: If you are not sure that the ceiling outlet box is grounded, contact a licensed electrician for advice. Connect the green grounding lead from the motor bracket and hanging bracket to the grounding conductor of the supply from the ceiling (this may be a bare copper or green Insulated wire) using the wire nut provided. HANGING BRACKET MOTOR BRACKET 5 FOUR SEASONSTM III HUGGER CONNECTING THE WIRING Step 11a. Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing twith a wire nut. Connect in this order: · GREEN leads from the mounting plate and fan to GROUND conductor of power source. [. . . ] Changing Light Bulbs Be sure to turn power to the fan OFF at the wall switch or circuit breaker before changing light bulbs. Exceeding the rated maximum allowable wattage for the fan will burn out the fan electronics module and void the warranty. PROBLEM FAN WILL NOT START 3-SPEED POSSIBLE REMEDIES. . Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making sure the power is turned off during this inspection. Check the screws holding the blade holders to the flywheel (or direct drive motor). [. . . ]