User manual CASABLANCA FAN COMPAGNY FOURSEAS3

[. . . ] 14 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual completely and carefully. CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure. BEFORE YOU START · All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical codes. The National Electric Code requires proper grounding as a precaution against electrical shock. · This fan is designed to be installed on an existing electrical outlet box. [. . . ] Remove the three mounting screws from the switch housing plate ready for the next step. SWITCH HOUSING PLATE SWITCH HOUSING INSTALLATION Step 6. Position the switch housing assembly on the switch housing plate and align the holes in the switch housing with the holes in the plate. Secure the switch housing assembly by reinstalling the three screws removed in the previous step. CAUTION!Do not pinch wires between the switch housing assembly and the plate. MOUNTING SCREW (3) 5 FOUR SEASONSTM III CROSSBAR MOUNTING BRACKET INSTALLATION HANGING THE FAN Step 7. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Rotate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening. NOTE: Independent control of the light fixture using a W-8 requires an additional power wire run from the wall switch to the fan. D1 OPTION WIRE SLOT PIN BALL CAPPED BLUE D1-OPTION WIRE ON 3-SPEED ONLY FOR INDEPENDENT W-8 LIGHT CONTROL CANOPY ELECTRICAL CONNECTIONS PULL CHAIN OR Step 8a. Attach the fan wires to the ceiling fixture outlet WIRE NUT box wiring by twisting the bare ends of the wires together W-4 CONNECTIONS and then securing with a wire nut. PROCEED TO YOUR FAN'S CONTROL FEATURE SECTION ON THE PAGE 13. BLADE HOLDER SCREW (2 PER BLADE HOLDER) FOB 7 FOUR SEASONSTM III (OUTSIDE USA INSTALLATION) FAN INSTALLATION OUTSIDE THE USA - EXCLUDING MODELS ENDING IN `E' If you do not have an existing fixture located where you wish to place your Casablanca fan, a new ceiling fixture outlet box must be installed (use an outlet box marked acceptable for fan support) and an electrical cable to run it. This box must be secured to the ceiling according to the outlet box manufacturer's instructions. Vaulted or Cathedral Ceiling Installations Your Casablanca fan may be installed on a vaulted or cathedral ceiling in the same manner as described for a flat ceiling. The Hang-Tru® mounting system makes it possible to hang your fan on sloped ceilings up to a 32° angle. Using Existing Ceiling Fixture Outlet Box After turning electrical power off, lower the old fixture to expose the wiring and the ceiling fixture outlet box. Cut the fixture wires or if wire nuts have been used, unscrew them and disconnect the wires. After removing the old fixture, check the outlet box to sure that it is supported by a joist or beam across its upper surface. If not, a 2" x 4" stud must be installed. OUTSIDE USA - SECONDARY SUPPORT INSTALLATION PARTS OUTLET ADAPTOR PLATE 6" OUTLET BOX CABLE 3 /8"- 7 LAG SCREW (5") FENDER WASHER SPRING LOCK HOOK OUTSIDE USA - MOUNTING SECONDARY SUPPORT PARTS TO OUTLET BOX WARNING: MOUNT ONLY TO AN OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT ···· ADVERTISSEMENT: ASSEMBLER UNIQUEMENT À UNE BÔITE DE SORTIE JUGÉE ACCEPTABLE POUR RETENIR UN VENTILATEUR. Before beginning Step 1, follow Steps A-C on Page 3. Remove the knockout plug in the center of the outlet box or drill a 1/2" hole for the lag screw to pass through. Then drill a 1/4" guide hole into the joist or beam to a depth of 3 inches. Route the outlet box wires through the /2" diameter outer hole of the outlet adaptor plate. Line up the slotted holes and four canopy screw holes in the crossbar mounting bracket and outlet adaptor plate with the 8-32 mounting holes in the outlet box. Install the two 8-32 X 21/4" (1") screws and flat washers in fan hardware kit and tighten securely by hand only! [. . . ] To install a W-4 wall control in place of an existing wall switch, follow the instructions on the W-4 package. Note: No rewiring is required if the fan is replacing an existing light fixture. Failure to set the pull-chain speed to HIGH can result in faulty operation of the fan and damage to the W-4 wall control. To confirm fan is set to HIGH: Turn W-4 fan speed switch to 'HI' - set fastest fan speed with pull chain. R 3-SPEED o OPTIONAL WALL CONTROL o W-8 The W-8 wall control provides separate control of fan and light with two separate knobs from a convenient wall location. [. . . ]