User manual CASABLANCA FAN COMPAGNY CAPISTRANO

[. . . ] For best performance and for your warranty to be valid, use only genuine Casablanca blades, light fixtures, and accessories. SAFE USE · The blades in each pack are matched for equal weight to assure smooth fan operation. If more than one fan is being installed, be careful not to mix blades from different cartons. · Inspect the contents of your carton for possible shipping or handling damage and report any such damage directly to your authorized Casablanca dealer. · It is always a good idea to have an assistant to help with the installation. [. . . ] Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole. Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet box. Tighten the screws firmly by hand only, being careful not to bend the bracket by over tightening. CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket. CEILING FAN APPROVED OUTLET BOX CEILING WIRING CROSSBAR MOUNTING BRACKET FLAT WASHER RIDGE SIDE DOWN GREEN GROUND WIRE OUTLET BOX MOUNTING HARDWARE CANOPY HARDWARE CANOPY SCREW (4) CANOPY HATCH CANOPY LOCK WASHER (4) CANOPY CANOPY INSTALLATION Step 2. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4 long canopy screws and canopy lock washers. Note: On sloped ceilings, align the canopy opening towards the top or room peak. CROSSBAR MOUNTING BRACKET INSTALLED CANOPY CANOPY LOCK WASHERS CANOPY SCREWS 4 CAPISTRANO Casablanca HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. Fan Hanging Weight is 24 lbs BALL CAPPED BLUE D1-OPTION WIRE ON 3-SPEED ONLY FOR INDEPENDENT W-8 LIGHT CONTROL SLOT PIN Note: Independent control of the light fixture using a W-8/W-811 requires an additional independent power wire run from the wall switch to the fan. Attach the fan wires to the ceiling fixture outlet box wiring by placing the bare ends of the wires side by side and then securing with a wire nut. · GREEN leads from mounting plate and fan to GROUND conductor of power source. · WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box. · BLUE wire and BLACK power wire from fan to BLACK power wire in ceiling outlet box. Secure with wire nut. WIRE NUT 2 BLACK WIRES 2 WHITE WIRES 3 GREEN WIRES CANOPY HATCH INSTALLATION Step 5. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Straighten the fan, then check to ensure that there is no movement between the canopy and ceiling or Hang-Tru ball and top support shaft. CANOPY HATCH LOCK WASHER CANOPY SCREW TILT THE FAN TO INSTALL LAST CANOPY SCREW Note: Write down the Serial Number and the model number for future reference. 5 CAPISTRANO Casablanca INSTALLING THE BLADE/BLADE HOLDER TO FAN MOTOR PREPARATION Step 8. To reach the blade holder mounting holes in the fan motor the dummy switch housing must be removed. Take out the two 5-32 X 9/32" screws securing the dummy switch housing and remove. Put the two (2) screws aside for the moment, they will be used in Step 15 to install the switch housing after the blades are installed. Line up the two inner clearance holes in the cap with the two threaded holes in the switch mounting plate standoffs. Before continuing to the next step check that a wire or component inside the switch housing will not be pinched as it is installed. Use the two (2) 5-32 X 9/32 screws removed in Step 8 to install the switch housing assembly. [. . . ] Changing Light Bulbs Be sure to turn power to the fan OFF at the wall switch or circuit breaker before changing light bulbs. Exceeding the rated maximum allowable wattage for the fan will burn out the fan electronics module and void the warranty. PROBLEM FAN WILL NOT START 3-SPEED POSSIBLE REMEDIES. . Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making sure the power is turned off during this inspection. Check the screws holding the blade holders to the flywheel (or direct drive motor). [. . . ]