User manual CASABLANCA FAN COMPAGNY BRESCIAGALLERY

[. . . ] BRESCIATM (GALLERY EDITION) OWNER'S MANUAL 21 CONTENTS INTRODUCTION . 19 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual completely and carefully. CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure. BEFORE YOU START · All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical codes. The National Electric Code requires proper grounding as a precaution against electrical shock. [. . . ] The remaining wire is to be connected to the other black wire on the W-32. Install the wall plate with the two short colormatched screws provided. Repeat steps 1 through 7. SWAP THESE TWO WIRES WHEN NECESSARY (SEE NOTE BELOW) R R END OF LINE IN LINE NOTE: If wall control operation is reversed (fan switch controls lights and light switch controls fan) turn off the power at the breaker or fuse panel, then swap the two W-32 black/white stripe wires. 11 R INTELI·TOUCH OPERATION o POWER The button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. POWER must be left on to retain a previously set fan speed or light level. INTELI·TOUCH OPERATION o SPEED CONTROL There are six individual speed settings for the fan; each speed is indicated by an audible tone of increasing pitch. The fan blades will start rotating at the slowest speed, and will increase in steps. The fan speed is now in memory and will automatically come on at the same speed each time the button is used. To lower speed, turn the fan on by pressing turn fan off, then on by pressing and holding the button until the desired speed is reached. When the fan is on, you may increase the speed by pressing and holding the button until the desired speed is reached, then release it. FAN CONTROL ON - OFF R A momentary press of the FAN button TO CHANGE SPEED Press and hold FAN button longer than one second INTELI·TOUCH OPERATION o REVERSING AIRFLOW The direction of airflow can be changed from downward to upward or from upward to downward. Note: A four-toned signal indicates the command was accepted by the fan. A few seconds later the fan will slow to a stop and then reverse direction. INTELI·TOUCH OPERATION o LIGHT button for less To turn the lights off and on, press and release the than one second. After one second the lights come on at their lowest level and gradually become brighter. The brightness level is now in the fan memory and will automatically come on at the same brightness the next time the button is used. To maintain this level of brightness, press the button for less than one second. To lower the brightness, turn the lights off, then press and hold the button until the desired brightness level is reached. When the light is on, you may increase the brightness level by pressing and holding the button until the desired level is reached, then release it. LIGHT CONTROL ON - OFF A momentary press of the LIGHT button TO CHANGE BRIGHTNESS R PRESS AND HOLD LIGHT BUTTON LONGER THAN ONE SECOND AUTOMATIC DEMONSTRATION PROGRAM Programmed into every Inteli-Touch Series fan is an Automatic Demonstration Program. It can be used to fully demonstrate and test the operation of the fan. Immediately operate the buttons in the following sequence: FAN - LIGHT FAN - LIGHT FAN A multi-tone signal will verify the start of the test program which proceeds as follows: · Lights slowly increase to full intensity. · Fan turns off with audio tones (blades coast for a short time). It will continue to repeat until the is turned off for more than three seconds, cancelling the program. + + + + 12 R INTELI·TOUCH OPERATION o LIGHT-MINDER® PROGRAM The Light-Minder program automatically turns OFF the fan mounted lights after two hours. Immediately operate the buttons in the following sequence: + + + 4. The fan and light will operate normally using the buttons to turn them on and off. [. . . ] You may still turn the light ON and OFF (or OFF and ON) manually for temporary lighting, but the light will continue to operate automatically at its programmed times. 6 5 4 3 2 1 SECURITY AUTO SAVER SECURITY TEST REVERSE WINTER SECURITY Replace batteries when "Lo" is displayed AUTO-SPEED: Thermostatic fan speed control SECURITY: Lights ON and OFF automatically REVERSE: Change airflow up or down SAVER: Lights turn OFF after 1 hour TEST: Tests all fan and light functions WINTER: Draft-free heat recirculation SECURITY MODE CYCLE 1. Off for 60 minutes 17 R COMFORT·TOUCH o CHANGING CHANNELS - CONTROL Changing the control channel 1. Press fan up or down buttons to change the number to a unique number from 49 to 63. You will need to repeat this step any time you remove the remote control batteries. [. . . ]