User manual CASABLANCA FAN COMPAGNY BRESCIA

[. . . ] 13 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual completely and carefully. CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure. BEFORE YOU START · All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical codes. The National Electric Code requires proper grounding as a precaution against electrical shock. · This fan is designed to be installed on an existing electrical outlet box. [. . . ] Attach the blades to the blade holders by first pressing the blade badge into the blade, then installing the blade holder using the four blade screws and flat washers provided for each blade. For 3-Speed models (with pull chain), please see the directions on Page 9. For Inteli·Touch (wall control) operation, please see the instructions on Page 10. PAGE 9 PAGE 10 R 8 3-SPEED o OPERATION Pull-chain switches on the fan control the fan and lights. First pull: fan ON, low speed Second pull: medium speed Third pull: high speed Fourth pull: fan OFF Direction of blade rotation is controlled by the reverse slide switch on the side of the switch housing. No changes in household wiring are required. REVERSE SWITCH FAN & SPEED CONTROL PULL CHAIN SWITCH 3-SPEED TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents. Blades: Wood finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be applied for added protection and beauty. The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated for life. Changing Light Bulbs Be sure to turn power to the fan OFF at the wall switch or circuit breaker before changing light bulbs. Exceeding the rated maximum allowable wattage for the fan will burn out the fan electronics module and void the warranty. PROBLEM FAN WILL NOT START 3-SPEED POSSIBLE REMEDIES. . Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making sure the power is turned off during this inspection. Check the screws holding the blade holders to the flywheel (or direct drive motor). Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s) as neccessary. Make sure all screws in the motor housing are snug, but not overly tight. Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or have fallen off the wire splices. Let fan run at high speed for two (2) hours If new, "break-in" may be required - run at higher speed for several days FAN WOBBLES OR SHAKES EXCESSIVELY FAN NOISY DURING OPERATION BREAK-IN PERIOD DOES NOT RUN ON LOW SPEED FAN RUNS SLOWLY IN EITHER DIRECTION IF ROTATION IS STARTED BY HAND; WILL NOT REVERSE: Defective reverse switch; defective capacitor; or open motor winding: Replace reverse switch assembly; replace PCB assembly; or replace motor unit. FAN WILL NOT OPERATE AT PROPER SPEEDS OR WILL NOT OPERATE AT ANY SPEED: Defective three-speed pull-chain switch assembly; or defective capacitor: Replace three-speed pull-chain switch assembly; or replace PCB assembly. For questions or to locate the nearest Casablanca Authorized Service Center call toll free: 1-888-227-2178 Or visit us on the web at: www. CasablancaFanCo. com 9 R INTELI·TOUCH© INSTALLING THE W-32 WALL CONTROL The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. No other light fixtures or electrical appliances may be confan (for example, dimmer, fan speed control, etc. ). nected on the circuit controlled by the W-32 wall control. INTELI·TOUCH o SINGLE W-32 INSTALLATION CAUTION! [. . . ] This seven hour pattern will repeat continuously so that a different pattern of lighting is seen each day of the week. To cancel the Home-Safe Program, turn the off for three seconds. INTELI·TOUCH OPERATION o FAN-MINDERTM PROGRAM The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the speed of the fan each two-hour interval to compensate for the cooling night air. Immediately operate the buttons in the following sequence: + + + 4. [. . . ]