User manual CASABLANCA FAN COMPAGNY BELLA

[. . . ] 10 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual completely and carefully. CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure. BEFORE YOU START · All wiring must be in accordance with the National Electric Codes and the appropriate local electrical codes. The National Electric Codes requires proper grounding as a precaution against electrical shock. · This fan is designed to be installed on an existing electrical outlet box. [. . . ] Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet box. Tighten the screws firmly by hand only, being careful not to bend the bracket by over tightening. CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket. CEILING FAN APPROVED WIRING BOX CEILING WIRING RIDGE SIDE DOWN CROSSBAR MOUNTING BRACKET GREEN GROUND WIRE FLAT WASHER APPROVED OUTLET BOX HARDWARE CANOPY HARDWARE CANOPY SCREW (4) CANOPY HATCH CANOPY CANOPY LOCK WASHER (4) 4 BELLATM CANOPY INSTALLATION Step 2. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4 long canopy screws and canopy lock washers. Note: On sloped ceilings, align the canopy opening towards the top or room peak. CROSSBAR MOUNTING BRACKET INSTALLED CANOPY CANOPY LOCK WASHERS CANOPY SCREWS HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. NOTE: The fan weight is 30 pounds. BALL SLOT PIN CANOPY ELECTRICAL CONNECTIONS Step 4. Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut. Connect in this order: · GREEN leads from mounting plate and fan to GROUND conductor of power source. · WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box. · BLACK wire from fan to black (or red) POWER wire in ceiling fixture outlet box. Secure with wire nut. WIRE NUT GREEN WIRES (3) BLACK WIRES (2) WHITE WIRES (2) 5 CANOPY HATCH INSTALLATION Step 5. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Straighten the fan, then check to ensure that there is no movement between the canopy and ceiling or Hang-Tru ball and top support shaft. CANOPY HATCH LOCK WASHER TILT THE FAN TO INSTALL LAST CANOPY SCREW CANOPY SCREW BLADE & BLADE HOLDER HARDWARE BLADE SCREW (4 PER BLADE) BLADE HOLDER SCREW (2 PER BLADE) BLADE HOLDER BLADE BADGE BLADE BADGE INSTALLATION Step 8. Attach the blades to the blade holders by first pressing the blade badge into the blade, then installing the blade holder using the four blade screws and flat washers provided for each blade. Repeat for each blade assembly. BLADE BADGE BLADE BLADE HOLDER BLADE SCREW (4 PER BLADE) BLADE ACCESS PLATE REMOVAL Step 9. Install and tighten screws by hand only. Rocker Light Switch Step 1. Orient the control holder as shown and line up the two outer mounting holes with those on the switch. Install and tighten screws by hand only. VERSA·TOUCH o HOLDER INSTALLATION / STORAGE Wall Installation Step 1. Use the 1" wood screws in either the inner or outer mounting holes. Note: The wall anchors and 6-32 x 1" screws may be used in situations where mounting to a stud is not possible. [. . . ] Blades: Wood finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be applied for added protection and beauty. The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated for life. Changing Light Bulbs Be sure to turn power to the fan OFF at the wall switch or circuit breaker before changing light bulbs. [. . . ]