User manual CASABLANCA FAN COMPAGNY BELAIRHALO

[. . . ] CONTENTS INTRODUCTION MOUNTING RECOMMENDATIONS FAN INSTALLATION CONTROL FEATURES: INTELI·TOUCH OPERATION INTELI·TOUCH TROUBLESHOOTING INTELI·TOUCH 2 OPERATION INTELI·TOUCH 2 TROUBLESHOOTING 1 2 3 9 12 13 15 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual completely and carefully. CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure. BEFORE YOU START · CAUTION: RISK OF ELECTRICAL SHOCK!All wiring must be performed in accordance with national and local electrical codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician. [. . . ] N0TE: If wall control operation is reversed (fan switch controls lights and light switch controls fan) turn off the power at the breaker or fuse panel, then swap the two W-32 black/white stripe wires. INTELI·TOUCH DUAL W-32 INSTALLATION CAUTION!Ensure power is turned OFF at the breaker or fuse panel before starting installation. To control the fan and lights from two locations (a three-way circuit), use 2 W-32 wall controls. Remove the screws and switch plate from the existing switch box and the screws holding the switch in the switch box. Pull the existing switch from the switch box to expose the wire connections. Determine which wire is connected to the common terminal of the 3-way switch. Connect this wire to the remaining black/white striped wire on the W-32 control. The remaining wire is to be connected to the other black wire on the W-32. Connect the green ground wire coming from the back of the W-32 control to the ground wire in the switch box. Install the wall plate with the two short color-matched screws provided. Repeat steps 1 through 7. NOTE: If wall control operation is reversed (fan switch controls lights and light switch controls fan) turn off the power at the breaker or fuse panel, then swap the two W-32 black/white stripe wires. 9 Inteli·TouchTM INTELI·TOUCH OPERATION POWER The button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. POWER must be left on to retain a previously set fan speed or light level. POWER POWE INTELI·TOUCH OPERATION SPEED CONTROL FAN CONTROL A momentary press of the FAN button Press and hold FAN button longer than one second TO CHANGE SPEED ON - OFF There are six individual speed settings for the fan; each speed is indicated by an audible tone of increasing pitch. The fan blades will start rotating at the slowest speed, and will increase in steps. The fan speed is now in memory and will automatically come on at the same speed each time the FAN button is used. To maintain this level of speed, FAN turn the fan on by pressing less than one second. To lower speed, FAN turn fan off, then on by pressing and holding the button until the desired speed is reached. When the fan is on, you may increase the speed by pressing and holding the FAN button until the desired speed is reached, then release it. The direction of airflow can be changed from downward to upward or from upward to downward. Press the REVERSE button. INTELI·TOUCH · REVERSING AIRFLOW Note: A four-toned signal indicates the command was accepted by the fan. A few seconds later the fan will slow to a stop and then reverse direction. INTELI·TOUCH OPERATION LIGHT To turn the lights off and on, press and release the than one second. LIGHT button for less LIGHT CONTROL CYCLES THROUGH SEQUENCE: 1. Up light only The sequence is, when the power is on: First touch of the light button--both lights come on Second touch of the light button--down light only Third touch of the light button--up light only To vary the light brightness at each touch level: Make sure where you are in the sequence to the right. [. . . ] But, if the lights are left on, they will automatically shut off after two hours. To cancel the Light-Minder Program, turn the POWER off for three seconds. FAN + FAN + LIGHT + LIGHT INTELI·TOUCH2 OPERATION SAFE-EXIT PROGRAM The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off, enabling you to exit your home before the lights go out. Immediately operate the buttons in the following sequence: FAN + FAN + LIGHT + LIGHT After you hear the confirming audio tones from the fan - immediately press 4. After a total of thirty seconds has elapsed, the lights will be off completely. [. . . ]