User manual CASABLANCA FAN COMPAGNY BELAIR

[. . . ] 18 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual completely and carefully. CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure. BEFORE YOU START · All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical codes. The National Electric Code requires proper grounding as a precaution against electrical shock. · This fan is designed to be installed on an existing electrical outlet box. [. . . ] The brightness level is now in the fan memory and will automatically come on at the same brightness the next time the button is used. To maintain this level of brightness, press the button for less than one second. To lower the brightness, turn the lights off, then press and hold the button until the desired brightness level is reached. When the light is on, you may increase the brightness level by pressing and holding the button until the desired level is reached, then release it. LIGHT CONTROL ON - OFF: R A momentary press of the LIGHT button CHANGE BRIGHTNESS: PRESS AND HOLD LIGHT BUTTON LONGER THAN ONE SECOND AUTOMATIC DEMONSTRATION PROGRAM Programmed into every Inteli-Touch Series fan is an Automatic Demonstration Program. It can be used to fully demonstrate and test the operation of the fan. Immediately operate the buttons in the following sequence: FAN - LIGHT FAN - LIGHT FAN A multi-tone signal will verify the start of the test program which proceeds as follows: · Lights slowly increase to full intensity. · Fan turns off with audio tones (blades coast for a short time). It will continue to repeat until the is turned off for more than three seconds, cancelling the program. + + + + 11 R INTELI·TOUCH OPERATION o LIGHT-MINDER® PROGRAM The Light-Minder program automatically turns OFF the fan mounted lights after two hours. Immediately operate the buttons in the following sequence: + + + 4. The fan and light will operate normally using the buttons to turn them on and off. But, if the lights are left on, they will automatically shut off after two hours. To cancel the Light-Minder Program, turn the off for three seconds. INTELI·TOUCH OPERATION o SAFE-EXIT® PROGRAM The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off, enabling you to exit your home before the lights go out. Immediately operate the buttons in the following sequence: + + + After you hear the confirming audio tones from the fan - immediately press 4. After a total of thirty seconds has elapsed, the lights will be off completely. Note: Both Light-Minder and Safe-Exit programs can run at the same time, however the dimmer cannot be used, the light may only be turned ON/OFF. INTELI·TOUCH OPERATION o HOME-SAFE® PROGRAM The Home-Safe Program makes an unoccupied home appear occupied by turning the lights on and off at random times. Immediately operate the buttons in the following sequence: + + + 4. The lights will now be automatically cycled on and off in a controlled sequence as follows: On 1 hour, off 1 /2 hour, on 2 hours, off 1 hour, on 1/2 hour then off 2 hours. This seven hour pattern will repeat continuously so that a different pattern of lighting is seen each day of the week. To cancel the Home-Safe Program, turn the off for three seconds. INTELI·TOUCH OPERATION o FAN-MINDERTM PROGRAM The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the speed of the fan each two-hour interval to compensate for the cooling night air. Immediately operate the buttons in the following sequence: + + + 4. A timer is now initiated and the fan will reduce one speed for each two-hour interval. [. . . ] Press and hold the and buttons together until the display shows 'cc' (for Change Channel), then release. Do not reset the channel on other fans in your home during this 110 second period. COMFORT·TOUCH o DUAL REMOTE CONTROL - BASE A second remote control can be purchased from your dealer to provide dual remote control of one fan. Because the fan could be confused by two controllers signaling different information it is necessary to set a BASE control and an AUXILIARY control. Where two remote controls are used to control a single fan, they must be set so that: · BOTH controls are set to the SAME channel. [. . . ]