User manual CARVIN USM16BP

[. . . ] If the unit has been pre-installed from the factory, you can follow these brief instructions to get you going quickly; REGULATIONS AND SERVICING This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. The circuits inside the receiver and transmitter have been precisely adjusted for optimum performance and compliance with federal regulations. To do so will void the warranty, and may cause improper operation. 1. [. . . ] CARVIN and the shipping company are not liable for any damage caused by improper packing. Please allow several days for the rest of your order to arrive before inquiring. RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual for your records. Keep your portion of the card and return the portion with your name and comments to us. HANDHELD MIC TRANSMITTER USM16MC Polar Pattern RF Power Output Spurious Emissions Dynamic Range Battery Current Consumption Battery Life Dimensions Net Wt (no battery) Accessory Included Warranty Unidirectional 3 mW Under federal regulations >100 dB AA 1. 5v alkaline qty 2 30 mA typical Approx. 12. 7 oz (360 grams) mic clip 90 days Net Weight Accessories Warranty For your records, you may wish to record the following information. Serial No. _____________________ Invoice Date_______________ c 12340 World Trade Drive, San Diego, CA 92128 USM16 1209 USM16-KIT INSTALLATION PROCEDURE: FOLLOW STEPS (A) THROUGH (E). LOOSEN AND REMOVE THESE TWO SCREWS KEEP FOR STEP (C) SLIDE THIS TAB INTO THE CONNECTOR ON CIRCUIT BOARD A B C D ANTENNA 1 SECURE CIRCUIT BOARD WITH SCREWS FROM (A) CONNECT THIS WIRE TO THE INTERNAL CONNECTOR ON YOUR CARVIN MIXER ANTENNA 2 (USE BOTH ANTENNAS AT ALL TIMES) E MOUNT THE UNIT(S) AND BRACKET TO YOUR CARVIN MIXER WITH SUPPLIED SCREWS FRONT PANEL CONTROLS TWO USM16 RECEIVERS MOUNTED WITH THE REQUIRED USM16-KIT LARGE CONSOLES CAN ACCEPT UP TO TO 4 RECEIVERS (2 USM16-KITs) 5 1 2 3 4 5 USM16 RECEIVER FRONT PANEL FEATURES 1. CHANNEL SELECTOR Use a small screwdriver to select your desired channel. RF LEVEL LED The RF level is displayed by an LED which allows you to estimate the RF signal strength. Use both antennas at all times for best operation. TIPS TO OBTAIN THE BEST WIRELESS RESULTS 1. Position the receiver so that it has the fewest possible obstruction between it and the normal location of the transmitter. The transmitter and receiver should be as close together as conveniently possible. The receiver antenna should be in the open and away from any metal or cement walls. Remove the battery if the transmitter is not used for a period of time. IMPORTANT RF OPERATION NOTES Please note that wireless frequencies are shared with other audio services: According to Federal Communications Commission regulations, "Wireless microphone operations are unprotected from interference from other licensed operations within the band. If any interference is received by any Government operation, the wireless microphone must cease operation. . . " If you encounter receiving interference (from other than an operating TV station), often it can be eliminated by adjusting the receiver's antenna. LIMITED WARRANTY 90 days on all wireless electronic components. Does not cover cables, connectors, or broken parts caused by normal wear and tear or by dropping. Carvin assumes no responsibility for horn drivers or speakers damaged by this unit. This warranty does not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions. This warranty is in lieu of all other warranties, expressed or implied. No representative or person is authorized to represent or assume for Carvin any liability in connection with the sale or servicing of Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. RETURNING AN ITEM Before you return an item, please visit www. carvinservice. com and review the TROUBLE SHOOTING guide to verify that you have a real problem. [. . . ] Use the mini screwdriver to first set the Sensitivity switch to 0 for instruments or -20 for microphones. Use the mini screwdriver to make fine gain adjustments to the Sensitivity AF Gain for optimal transmitter volume. When the indicator becomes very dim or goes out, replace the batteries for continued operation. If you encounter signal interference, try selecting an alternate channel. [. . . ]