User manual CARVIN RX 1200

[. . . ] CARVIN ENGINEERING DATA RX800, RX1200, RX1200R MIXERS OPERATING MANUAL DISTORTION-FREE LIMITERS The purpose of a limiter is to hold down peaks so the amp won't distort even with extra hot input signals (this protects your expensive speakers). In addition, limiters can increase your amp's average output by 3 db or more. Part of Carvin's design uses the more expensive, distortion-free linear "opto isolators". Unlike amps that use FET controlled limiters which can inject small amounts of distortion, our limiters keep your sound pure and uncolored! [. . . ] MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAIN PLUG INTO A POWER SOCKET. Avoid spilling liquids or allowing any other foreign matter inside the unit. The panel of your unit can be wiped from time to time with a dry or slightly damp cloth in order to remove dust and bring back the new look. As with all pro gear, avoid prolonged use in caustic environments (salt air). When used in such an environment, be sure the mixer is adequately protected by a cover. CAUTION RISK OF ELECTRIC SHOCK REFER SERVICING TO QUALIFIED SERVICE PERSONNEL!THIS UNIT CONTAINS HIGH VOLTAGE INSIDE! RX1200 BLOCK DIAGRAM LEFT RIGHT MON 1 MON 2 EFF (x2) CHANNEL 12 (or 8) BYPASSES BREAK SWITCH SEVEN BAND GRAPHIC EQUALIZER LEFT (AMP1) LEFT XLR OUT TO AMP 1 INSERT RIGHT XLR OUT MIC MIC PRE PAD THREE BAND CHANNEL TONE CONTROLS PAN LINE IN PAD (-20dB bal. ) (-26dB unbal. ) GAIN HI MID LOW CHANNEL LEVEL EFF SND (x2) LINE - INS SWITCH L MON 1 TAPE OUT BREAK SWITCH R MAIN L-R LEVEL SEVEN BAND GRAPHIC EQUALIZER RIGHT (AMP2) TO AMP 2 INSERT LINE (INSERT) CHANNEL MON 2 MONO (SUB) 1/4" OUT SUB X-OVER 120Hz L TAPE INPUT R TAPE OUT LEVEL SEVEN BAND GRAPHIC EQUALIZER MONITOR1 (AMP3) TAPE IN LEVEL MONITOR 1 LEVEL SEVEN BAND GRAPHIC EQUALIZER MONITOR2 (AMP4) MONITOR 1/4" OUT TO AMP 3 INSERT MONITOR 1/4" OUT TO AMP 4 INSERT STEREO DSP RETURNS (x2) MAIN DSP LEVEL (x2) MONITOR 2 LEVEL REAR INSERTS AND AMPS 1-4 GAIN REDUCTION FOR DSP DSP TO MONITORS 1-2 (x2) DSP SEND (x2) EXTERNAL SEND (x2) FROM FRONT PANEL INSERT CLIP LIMITER POWER AMP PROTECTION RELAY SPEAKER OUTPUTS 12340 World Trade Drive San Diego, CA 92128 858-487-1600 FAX 521-6032 RX1200 & 800 BLOCK DIAGRAM Part No. Date Revised Approved By: Date Approved Drawn By: Date Drawn E. PETERSEN 14JUN05 RX800, RX1200, RX1200R CONTROLS QUICK START UP If you're like most new owners, you're probably in a hurry to plug your mixer in and use it. With the mixer unplugged and the unit turned off, complete the following procedures: A. CONNECTING AC POWER TO YOUR MIXER · Be sure to plug your mixer into the proper voltage for your country, either 120V-60Hz or 240V-50Hz. · Use only a grounded (3 prong) power outlet to prevent a shock hazard. CONNECTING INPUTS TO YOUR MIXER · For balanced microphones, use a shielded cable and plug into the XLR MIC inputs. The LO and HI controls are shelving type with corner frequencies at 80Hz and 11. 5k Hz respectively. LEFT & RIGHT XLR OUTPUTS The LEFT and RIGHT balanced XLR line outputs are the same signals that feed the internal AMPS 1&2. MONITOR 1& 2 OUTPUTS The MONITOR 1 - 2 line outputs are the same signals that feed the internal MONITOR AMPS 3 & 4. Use these outputs for additional power amps or recording gear. 9 MIC CHANNEL FEATURES 1. LINE INPUT/INSERT JACK The LINE input is a 1/4" phone jack designed for balanced or unbalanced line or instruments. The line input can be used at the same time the mic input is being used. This jack becomes an insert when the INSERT switch is pushed "IN". 8 7 2. INSERT SWITCH This switch changes the function of the channel's 1/4" jack. Pressing the INSERT switch "IN" changes the jack into an INSERT with SEND and RETURN. This allows you to place effects on the channel after the GAIN control for lowest noise. [. . . ] Note: Make sure the phantom power is switched off before connecting or disconnecting microphones to the mixer. It is recommended to allow 5 seconds for the phantom power to discharge before making any microphone connections. 23. POWER LED The Power LED indicates when the mixer is powered on. REAR PANEL FEATURES RX1200, RX800 27 28 27 12 11 19 29 27. POWER CONNECTIONS The rear panel contains the POWER SWITCH and AC power cable connection. 28. [. . . ]