User manual CARROM TABLE HOCKEY

[. . . ] Close the front cover. 5 Load Paper 6 Install Mains Power Cord A. Adjust the paper guides at the right and rear of the paper cassette for the paper size you want. C. Press down on the paper to flatten it in all four corners, keeping the paper level below the guide. [. . . ] Complete reading this guide before connecting the Parallel or USB cables. –1– Version A Setting Up the MFC and PC to Work Together Before You begin • • You must set up the hardware and install the Brother Drivers before you can use your MFC as a printer and scanner in any Windows® application. Please purchase the appropriate cable if you intend to use USB. Use only a shielded parallel interface cable that is IEEE 1284-compliant and/or a USB cable that is no longer than 6 feet long (1. 8 meters). Follow the instructions in this guide for your operating system and interface. For Windows® 95/98/98SE/Me/2000 Users Step 1. Step 3. Turn the MFC power switch OFF and disconnect your MFC from your computer if you already connected an interface cable. Turn on your computer. For Windows® 2000 Professional, you must be logged on as the Administrator. Insert the CD-ROM into the CD-ROM drive. 1. (If any window does not appear after you insert the CD-ROM into the CD-ROM drive, use Windows® Explorer to run the setup. exe program from the root directory of the Brother CD-ROM. ) 3. Click Install Software. 4. Click MFC Software Suite in Main Application. Please see Note *1. 5. Click Install. 6. The InstallShield Wizard Setup window will appear briefly, followed by the PaperPort® Setup window. Click Yes. 7. When the PaperPort® Setup window displays your Name and Company, either change or accept them, and then click Next. 8. When the Choose Destination Location window displays the path where the PaperPort® files will be installed, either change or accept, and then click Next. 9. When the Register Today screen appears, click Next. When the MFC Software Suite Installation window appears, click Next to begin installing the MFC Software Suite. Follow the instructions on the screen. ( For Windows® 98/98SE/Me Users ) ( For Windows® 2000 Users ) 1. In the Add Printer Wizard window, select BRUSB: USB Printer Port, and then click Next. 2. Accept the default Printer name by selecting Yes, and then click Next. 3. Select Yes (recommended), and then click Finish. A test page will be printed so you can check the print quality. 1. When the Digital Signature Not Found dialog boxes appear, click Yes to install the driver. 4. If the test page is printed correctly, click Yes. If you click No, follow the prompts on the screen to correct the problem. 5. Select Yes to restart your computer, and then click Finish. 6. Click Yes to have the Control Centre loaded each time Windows® is started. Please see Note *3. 2. Select Finish to restart your computer. 3. Click Yes to have the Control Centre loaded each time Windows® is started. Please see Note *3. Printer and Scanner drivers have been installed and the installation is now complete. Printer and Scanner drivers have been installed and the installation is now complete. –3– For Windows NT® Workstation Version 4. 0 Users Step 1. Check that your computer is turned on. Step 3. Select Yes to restart your computer, and then click Finish. You must be logged on as the Administrator. Step 2. A. B. Connect the MFC to your PC with the Parallel Cable. (Same step as Windows 95/98/98SE/Me/2000 Users Step 3. , 1-11) Connect the parallel interface cable to the parallel interface port of the MFC and secure the wire clips. Connect the interface cable to the printer port of the computer and secure it with the two screws. [. . . ] For the location of your computer’s parallel printer port, see the User’s Guide for your computer. 13. Click Yes to have the Control Centre loaded each time Windows is started. Please see Note *3. Printer and Scanner drivers have been installed and the installation is now complete. For Apple® Macintosh® Step 1. Make sure your MFC power switch is turned OFF and your Macintosh is turned ON. QuickDraw® Driver for OS 8. 6/9. 0/9. 0. 4/9. 1 Users Step 4. Step 5. Connect the Filter Core and Cable Tie to the USB cable. [. . . ]