User manual CARROM SKITTLES

[. . . ] Do NOT remove the clear plastic starter sheet this will be ejected while the machine is warming up. Starter Sheet C. Holding the drum unit by its handles, insert it into the machine. B. If your paper size is A4 or Letter, extend the paper stopper by pulling it toward you. Do NOT remove the Starter Sheet! D. Close the top cover. (For A4 and Letter paper) 4 Load Paper 5 Install Mains Power Cord A. [. . . ] Make sure the print side is toward the fax machine and the paper level is stacked below the paper mark. The feeder can hold up to 200 sheets of paper, or up to 10 envelopes. Mains Power Cord Turn the power switch ON. Load the paper with the lever down Complete reading this guide before connecting the Parallel or USB cables. Version A –1– Setting Up the MFC and PC to Work Together Before You begin • • You must set up the hardware and install the Brother Drivers before you can use your MFC as a printer and scanner in any Windows® application. Please purchase the appropriate cable if you intend to use USB. Use only a shielded parallel interface cable that is IEEE 1284-compliant and/or a USB cable that is no longer than 6 feet long (1. 8 meters). Follow the instructions in this guide for your operating system and interface. For Windows® 95/98/98SE/Me/2000 Users Step 1. Step 3. Turn the MFC power switch OFF and disconnect your MFC from your computer if you already connected an interface cable. Turn on your computer. For Windows® 2000 Professional, you must be logged on as the Administrator. Insert the CD-ROM into the CD-ROM drive. 1. Insert the MFC Software Suite CDROM into your CD-ROM drive. If the model name screen appears, click on your model name. 2. Click your language. The CD-ROM main menu will appear. 3. Click Install Software. 4. Click MFC Software Suite in Main Application. Please see Note*1. 5. Click Install. 6. The InstallShield Wizard Setup window will appear briefly, followed by the PaperPort® Setup window. Click Yes. 7. When the PaperPort® Setup window displays your Name and Company, either change or accept them, and then click Next. 8. When the Choose Destination Location window displays the path where the PaperPort® files will be installed, either change or accept, and then click Next. 9. When the Register Today screen appears, click Next. A test page will be printed so you can check the print quality. 1. When the Digital Signature Not Found dialog boxes appear, click Yes to install the driver. 4. If the test page is printed correctly, click Yes. If you click No, follow the prompts on the screen to correct the problem. 5. Select Yes to restart your computer, and then click Finish. 6. Click Yes to have the Control Centre loaded each time Windows® is started. Please see Note*3. 2. Select Finish to restart your computer. 3. Click Yes to have the Control Centre loaded each time Windows® is started. Please see Note*3. Printer and Scanner drivers have been installed and the installation is now complete. Printer and Scanner drivers have been installed and the installation is now complete. –3– For Windows NT® Workstation Version 4. 0 Users Step 1. Check that your computer is turned on. Step 3. Select Yes to restart your computer, and then click Finish. You must be logged on as the Administrator. Step 2. A. B. Connect the MFC to your PC with the Parallel Cable. (Same step as Windows 95/98/98SE/Me/2000 Users Step 3. , 1-11) Connect the parallel interface cable to the parallel interface port of the MFC and secure the wire clips. Connect the interface cable to the printer port of the computer and secure it with the two screws. For the location of your computer’s parallel printer port, see the User’s Guide for your computer. 13. Click Yes to have the Control Centre loaded each time Windows is started. [. . . ] Click Yes to have the Control Centre loaded each time Windows is started. Please see Note*3. Printer and Scanner drivers have been installed and the installation is now complete. For Apple® Macintosh® Step 1. Make sure your MFC power switch is turned OFF and your Macintosh is turned ON. QuickDraw® Driver for OS 8. 6/9. 0/9. 0. 4/9. 1 Users Step 4. Step 5. Connect the Filter Core and Cable Tie to the USB cable. Connect the MFC to your Macintosh with the USB cable, and then turn the MFC power switch ON. Make sure you do NOT connect your MFC to your Macintosh. Step 2. Insert the CD-ROM into your CDROM drive. 1. When the window appears, doubleclick MFC Software Suite Installer. Installing MFC Software Suite Select your language 2. Click your language to install the printer and scanner drivers. After the installation is completed, the screen prompts you to restart your Macintosh. Step 6. Select the Printer. 1. [. . . ]