User manual CARROM PROSTICK HOCKEY

[. . . ] ■ For Parallel use a shield interface cable that is IEEE 1284-compliant. ■ Use only a parallel interface cable or USB interface cable that is not longer than 1. 8 meters. Control Panel 9 8 7 6 1 1. Options key For more details, see Chapter 1 "PROSTICK HOCKEY control panel overview" in the User's Guide. Table of Contents Step 1 1. 9. Setting Up the machine Removing the Protective Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ■ If INK EMPTY shows on the LCD after you install the ink cartridges, check to make sure the ink cartridges are installed correctly. Gently insert the black ink cartridge in the black ink position. 8 Press the cover down until it clicks. 9 0 Repeat Steps 5 to 8 to install each colour ink cartridge. The machine will enter a head cleaning cycle for approximately six minutes. CLEANING PLEASE WAIT 6 1 After the cleaning cycle is finished, the LCD shows; SET PAPER AND PRESS FAX START START CLEANING?1. YES 2. NO 2 3 The machine starts printing the PRINT QUALITY CHECK SHEET (only during initial ink cartridge installation). Step B:Alignment Check 1 The LCD shows: IS STEP "B" OK?1. YES 2. NO Check in Step A Check in Step B Step A:Colour Block Quality Check 1 The LCD shows: IS STEP "A" OK?1. YES 2. NO No. 5 600 DPI Do NOT select Check the quality of the four colour blocks printed on the sheet. (BLACK/CYAN/YELLOW/MAGENTA) 1 2 2 For 600 DPI, select the number from 1 to 8 that most closely matches the No. 0 sample and enter it using the dial pad. 600DPI ADJUST SELECT BEST # OK Poor 3 3 The LCD asks you if the print quality is OK for each colour. 1. YES 2. NO For 1200 DPI, enter the number from 1 to 8 that most closely matches the No. 0 sample. 1200DPI ADJUST SELECT BEST # The Quality check is now complete. 7 Mac® OS X 10. 1/10. 2. 1 or greater If all lines are clear and visible, press the key on the dial pad to go to STEP B Alignment Check. —OR— If you can see missing short lines, press the key on the dial pad and go to step 3. If another test print number is a better match for either 600 DPI or 1200 DPI, press the key to select NO and go to step 2. Mac® OS 8. 5-9. 2 1200 DPI Windows NT® 4. 0 Check the 600 DPI and 1200 DPI test print to see if No. 5 most closely matches the OK sample (No. 0). Press the key if No. 5 matches it. Windows® Parallel Windows® USB Make sure the paper is loaded in the paper tray. Press the Fax Start key. Press the key (YES), and then machine starts cleaning the colours. The machine starts printing PRINT QUALITY CHECK SHEET again and goes back to the first step of STEP A. Setting Up the machine 6 Colour Block Quality and Alignment Check When you have finished selecting the key (YES) or the key (NO) for each colour, the LCD shows: Step 1 Setting Up the machine Dial pad Menu/Set Receive Mode Fax/Start Stop/Exit 7 Selecting a Receive Mode Choose the mode which best suits your needs by pressing the Receive Mode key repeatedly. You connect an external telephone or external telephone answering machine to the machine. Yes No FAX ONLY The machine automatically answers every call as a fax. Yes FAX/TEL The machine controls the line and automatically answers every call. The application files will be copied to your computer. E When the Brother MFC Software Suite Installation window appears, click Next. Windows® 98/98SE/Me Users ➝ Go to page 15 Windows® 2000 Professional Users ➝ Go to page 17 Windows® XP Users ➝ Go to page 18 If an error message appears during the installation process, or if you have previously installed the MFC Software Suite, you will first have to uninstall it. From the Start menu, select Programs, Brother, Brother MFC Software Suite, Uninstall, and then follow the instructions on the screen. 14 Step 2 For Windows® 98/98SE/Me Users Only H When this screen appears, turn on the machine by plugging in the power cord. Connect the USB interface cable to your PC, and then connect it to the machine. Setting Up the machine J Accept the default Printer name by selecting Yes, and then click Next. Windows® USB K Select Yes (recommended), and then click Finish. A test page will be printed so you can check the print quality. Installing the Driver & Software . L It will take a few seconds for the installation screen to appear. Follow the instructions on the screen. If the test page is printed correctly, click Yes. If you click No, follow the prompts on the screen to correct the problem. I Select BRUSB: USB Printer Port, and then click Next. Continued 15 Step 2 Installing the Driver & Software For USB Interface Cable Users (For Windows® 98/98SE/Me/2000 Professional/XP) M Click Finish to restart your computer. N After the computer restarts, click Yes to have the Control Center loaded each time Windows is started. If you click No the Scan keys on the machine will be disabled. Even if you select NO, later you will be able to launch the Brother Control Center to use the Scan to key. See “AutoLoad the Brother Control Center”, Chapter 14 in the On-Line Documentation (User’s Guide) on the CD-ROM. The Brother PC fax, Printer and Scanner drivers have been installed and the installation is now complete. 16 For Windows® 2000 Professional Users Only H When this screen appears, turn on the machine by plugging in the power cord. Connect the USB interface cable to your PC, and then connect it to the machine. K Click Finish to restart your computer. L . . I It will take a few seconds for the installation screen to appear. If the Digital Signature Not Found dialog boxes appear, click Yes to install the driver. Even if you select NO, later you will be able to launch the Brother Control Center to use the Scan to key. See “AutoLoad the Brother Control Center”, Chapter 14 in the On-Line Documentation (User’s Guide) on the CD-ROM. J . The Brother PC fax, Printer and Scanner drivers have been installed and the installation is now complete. 17 Installing the Driver & Software After the computer restarts, click Yes to have the Control Center loaded each time Windows is started. [. . . ] Follow the instructions on the screen. Setting Up the machine Step 2 Installing the Driver & Software For Parallel Interface Cable Users (For Windows® 95/98/98SE/Me/2000 Professional/XP) For Windows® XP Users Only G When this screen appears, connect the parallel interface cable to your PC, and then connect it to the machine. Turn on the machine by plugging in the power cord. H When the following screen appears, click Finish and wait as the PC restarts Windows and continues the installation. The Brother PC fax, Printer and Scanner drivers have been installed and the installation is now complete. . The installation of the Brother driver will automatically start. Follow the instructions on the screen. 24 Make sure that you have completed the instructions from Step 1 “Setting Up the machine”. 1 2 Turn on your computer. Connect the parallel interface cable to your computer, and then connect it to the machine. 6 The CD-ROM main menu will appear. [. . . ]