User manual CARROM BOWL-A-MANIA

[. . . ] After a few seconds, the print head will move left to its replacement position. Top Cover Control Panel Cover White Shipping Cover Ink Cartridge Covers White Shipping Cover WARNING If ink gets in your eyes, rinse them with water immediately and if irritation occurs, consult a doctor. We recommend that you install the ink cartridges from left to right in this order: Black, Cyan, Yellow, Magenta. Carefully remove the sealing tape from the bottom of the ink cartridge. Important To prevent spilling ink and staining your hands and clothing, peel the sealing tape gently and slowly. [. . . ] Press Mono Fax Start and go to Step 8 “Check Colour Block Quality and Alignment”. Peel in the direction away from you!Don't touch this part Opening 8 Check Colour Block Quality and Alignment STEP A: Colour Block Quality Check The LCD shows: IS STEP “A” OK?1. YES 2. NO The MFC starts printing the PRINT QUALITY CHECK SHEET (only during initial ink cartridge installation). Check the sheet to see if the quality and alignment are OK by following steps A and B. STEP B: Alignment Check The LCD shows: IS STEP “B” OK?1. YES 2. NO Check the quality of the four colour blocks printed on the sheet. —OR— If white horizontal lines appear in some colour blocks below, press 2 (NO). OK Poor 1 Check the 600DPI and 1200DPI test print to see if No. 5 most closely matches the OK sample ( 0 ). If No. 5 is the best match, enter 1 (YES) to go to (YES)—OR— Do NOT select The LCD asks you if the print quality is OK for each colour. BLACK OK?1. YES 2. NO } } 600 DPI 1200 DPI If another test print number is a better match for either 600DPI or 1200DPI, enter 2 (NO) to select it. For 600DPI, enter the number of the test print that most closely matches the 0 sample (1-8). 600DPI ADJUST SELECT BEST # Press 2 (NO) for any colour with a problem. The LCD shows: START CLEANING?1. YES 2. NO Press 1 (YES), then MFC starts cleaning the colours. Mono Fax Start. The After cleaning is finished, press MFC starts printing PRINT QUALITY CHECK SHEET again and goes back to the first step of STEP A. For 1200DPI, enter the number of the test print that most closely matches the 0 sample (1-8). 1200DPI ADJUST SELECT BEST # Page 2 BOWL-A-MANIA Control Panel Navigation Keys You can print a list of basic operational steps by pressing Reports, 1 . When the Setup Type window appears, select Standard, and then click Next. The Connect Cable window will appear. *1 MFC Software Suite includes Printer Driver, Scanner Driver, ScanSoft™ PaperPort®, ScanSoft™ Text Bridge®, PC-FAX software, Remote Setup and True Type fonts. PaperPort® is a document management application for viewing scanned documents. ScanSoft™ TextBridge®, which is integrated into PaperPort®, is an OCR application that converts an image into text and inserts it into your default word processor package. *2 If an error message appears during the installation process, or you have previously installed MFC Software Suite or MFL Pro, you will first have to uninstall it. From the Start menu, select Programs, Brother, Brother MFL Pro, Uninstall, and then follow the instructions on the screen. *3 Even if you select NO, later you will be able to launch the Brother Control Centre to use the Scan to key. See AutoLoad the Brother Control Centre, Chapter 13 in the Owner’s Manual on the CD-ROM. Page 4 43210987654321 43210987654321 43210987654321 43210987654321 654321 4321098767654321098765432121098765432109876543210987654321 4321098787654321098765432121098765432109876543210987654321 854321 43210987654321 8 4321098767654321098765432121098765432109876543210987654321 854321 87654321098765432121098765432109876543210987654321 4321098767654321098765432121098765432109876543210987654321 43210987654321 854321 4321098767654321098765432121098765432109876543210987654321 654321 854321 4321098767654321098765432121098765432109876543210987654321 854321 1 4321098767654321098765432121098765432109876543210987654321 854321 432109876765432109876543212109876543210987654321098765432 4321098787654321098765432121098765432109876543210987654321 54321 43210987654321 43210987654321 43210987654321 Please see NEXT PAGE Step 4. A. B. Connect the MFC to your PC with Parallel Cable. Connect the parallel interface cable to the parallel interface port of the MFC and secure the wire clips. Connect the interface cable to the printer port of the computer and secure it with the two screws. For the location of your computer’s parallel printer port, see the User’s Guide for your computer. For Parallel interface cable users Step 5. Follow the instructions on the screen. ( For Windows® 2000 Professional User ) ( For Windows® 95/98/98SE/Me Users ) 1. In the Connect Cable window, click Next. 2. When the above screen appears, click Finish and wait as the PC restarts Windows® and continues the installation. 1. In the Connect Cable window, click Next. 2. When the above screen appears, click Finish and wait as the PC restarts Windows® and continues the installation. 3. Click Yes to have the Control Centre loaded each time Windows® is started. Please see Note*3. The Brother PC fax, Printer and Scanner drivers have been installed and the installation is now complete. 3. When the Digital Signature Not Found dialog boxes appear, click Yes to install the driver. 4. Click Yes to have the Control Centre loaded each time Windows® is started. [. . . ] B. Connect the MFC to your PC with the Parallel Cable. Connect the parallel interface cable to the parallel interface port of the MFC and secure the wire clips. Connect the interface cable to the printer port of the computer and secure it with the two screws. For the location of your computer’s parallel printer port, see the User’s Guide for your computer. 13. Click Yes to have the Control Centre loaded each time Windows is started. [. . . ]