User manual CARROM 750-31

[. . . ] Before replacing internal parts, cleaning the printer or clearing a paper jam, make sure you have turned OFF the power switch and unplugged the AC power cord from the AC power outlet/socket. Do not handle the plug or AC power cord with wet hands. This constitutes an electric shock hazard. The fusing unit becomes extremely hot during operation. Wait until it has cooled down sufficiently before replacing consumable items. The fusing unit is marked with a caution label. Please do NOT take off or damage the label. This printer is heavy and weighs approximately 30. 5 kg (67. 3 lb). [. . . ] ☛ Caution: Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. IMPORTANT - For Your Safety To ensure safe operation the supplied three-pin plug must be inserted only into a standard three-pin power outlet that is properly grounded through the normal household wiring. Extension cords used with this printer must be three-pin plug type and correctly wired to provide proper grounding. Incorrectly wired extension cords may cause personal injury and equipment damage. The fact that the equipment operates satisfactorily does not imply that the power is grounded and that the installation is completely safe. For your safety, if in any doubt about the effective grounding of the power, call a qualified electrician. Disconnect device You must install this printer near a power outlet that is easily accessible. In case of an emergency, you must disconnect the power cord from the power outlet to shut off the power completely. IEC 60825 specification (220 to 240 volt model only) This printer is a Class 1 laser product as defined in IEC 60825 specifications. The label shown below is attached in countries where it is needed. Caution for LAN connection Connect this product to a LAN connection that is not subjected to over voltages. CLASS 1 LASER PRODUCT APPAREIL À LASER DE CLASSE 1 LASER KLASSE 1 PRODUKT IT power system (For Norway only) This product is also designed for an IT power system with phase-to-phase voltage 230V. This printer has a Class 3B laser diode which produces invisible laser radiation in the scanner unit. ☛ Caution: Use of controls or adjustments or performance of procedures other than those specified in this User’s Guide may result in hazardous radiation exposure. Geräuschemission / Acoustic noise emission (for Germany only) Lpa < 70 dB (A) DIN 45635-19-01-KL2 Wiring information (for UK) Important If you need to replace the plug fuse, fit a fuse that is approved by ASTA to BS1362 with the same rating as the original fuse. Never use a plug that does not have a cover. For Finland and Sweden LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT ☛ Varoitus!Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle. Om apparaten används på annat sätt än i denna Bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1. Warning - This printer must be earthed. The wires in the mains lead are coloured in line with the following code: ☛ Varning Green and Yellow: Blue: Brown: Earth Neutral Live If in any doubt, call a qualified electrician. Internal laser radiation Maximum radiation power: 5 mW Wave length: 780 - 800 nm Laser class: Class IIIb (Accordance with 21 CFR Part 1040. 10) Class 3B (Accordance with IEC 60825) 3 ■ Getting Started Carton Components Printer 1 2 3 4 5 9 8 7 6 CD-ROM (including User's Guide) Quick Setup Guide 1 Control Panel 4 Front Cover 8 Face-down 2 Paper Stopper 5 Paper Tray Output Tray 3 Face-down Output 6 Top Cover 9 Paper Support Tray Extension 7 Back Cover OPC Belt Cartridge AC Power Cord Toner Cartridges (Black, Cyan, Magenta and Yellow)*1 Repacking Kit*2 Parts/Paper Jam Locator Label*3 Carton components may differ from one country to another. Go to page 29 ■ Mac OS® X 10. 1 / 10. 2 Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Go to page 30 For Administrators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Go to page 32 13 For Administrators Macintosh® Network For Network Interface Users Macintosh® USB For USB Interface Cable Users Windows® Network For Network Interface Cable Users Windows® Parallel For Parallel Interface Cable Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Go to page 16 Windows® USB For USB Interface Cable Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Go to page 14 Step 2 Installing the Driver For USB Interface Cable Users 1. Installing the Driver and Connecting the Printer to your PC If the Found New Hardware Wizard appears on your PC, click the Cancel button. 4 Click Printer Driver. 1 Make sure the USB interface cable is NOT connected to the printer, and then begin installing the driver. If you have already connected the cable, remove it. A C C N L E 5 Click the Next button. Follow the on-screen instructions. 6 2 Select Standard Installation, and then click the Next button. Insert the CD-ROM into your CD-ROM drive. Follow the on-screen instructions. 3 Click Install Software icon on the menu screen. If you want to install the PS driver, select Custom and then follow the on-screen instructions. When the Select Components screen appears, check PS Printer Driver, and then continue following the on-screen instructions. 14 7 Select Local Printer with USB cable, and then click the Next button. 2. Setting your Printer as the Default Printer (For Windows® 2000/XP Users Only) 1 Click Start and then Printers and Faxes. Windows® USB 8 When this screen appears, make sure the printer’s power switch is on. [. . . ] Follow the on-screen instructions. 2 Connect the network interface cable to the printer, and then connect it to a free port on your hub. 6 From the Go menu, select Applications. 7 3 Turn on the printer’s power switch. Open the Utilities folder. 8 Open the Print Center icon. 4 Insert the CD-ROM into the CD-ROM drive. Follow the instructions on the screen. 28 For Network Interface Cable Users 9 Click the Add Printer. . . button. B From the Print Center menu, select Quit Print Center. 0 Select AppleTalk. Setup is now complete. A Select BRN_xxxxxx_P1_AT*1, and then click the Add button. *1 xxxxxx are the last six digits of the Ethernet address. [. . . ]