User manual CANON PIXMA MG5320 BROCHURE

[. . . ] Be careful not to get ink on yourself when handling these items. If the orange-colored protective film is not removed completely, problems with printing may occur. b Twist off and discard the orange protective cap located on the bottom of the ink tank. Protective Cap Do not press!Ink Port Note · At purchase, the printer is set to feed from the Auto Sheet Feeder. For details on how to change the paper source, refer to "Basic Printing" of the Quick Start Guide. [. . . ] · You can load A4, Letter, or B5-sized plain paper in the Front Feeder. When using any other type of paper, load it in the Auto Sheet Feeder. b Remove the orange protective cap from the Print Head and discard it. Auto Sheet Feeder e Write down the serial number located inside the Electrical Contacts Electrical Contacts printer. You will need this to register your product. Important · Do not touch the electrical contacts. · Do not touch the ink port. Front Feeder b Plug the power cord in the back of the printer and connect the other end to the wall outlet. Protective Cap Print Head Nozzles c Insert the ink tank into the right-hand slot and press the into place. Note Do not touch the print head nozzles and the electrical contacts. Serial Number Location mark on the ink tank until it clicks Loading Paper in the Auto Sheet Feeder a Load the paper in the Auto Sheet Feeder with the print side facing UP. c Firmly raise the Print Head Lock Lever until it stops. b Align the paper stack against the Cover Guide on the right side of the Paper Support. the left side of the paper stack. Paper Guide Print side facing UP. c Pinch the Paper Guide and slide it against d Insert the Print Head. d Make sure the ink lamp lights red. Cover Guide Important Plug the power cord all the way in, since it may be difficult to plug. Do not touch! Insert all ink tanks in order from right to left according to the colored label. c Press the POWER button to turn on the printer. e Lower the Print Head Lock Lever carefully. Loading Paper in the Front Feeder e Close the Top Cover. a Load the paper in the Front Feeder with the print side facing DOWN and the leading edge to the far side. b Align the right edge of the paper stack against the inner face of the Front Feeder, and the near and left edges with the Paper Size Mark. the left side of the loaded paper stack. Paper Guide Print side facing DOWN. c Pinch the Paper Guide and slide it against Important If the Top Cover is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Top Cover to return the Holder to the center. Important · The printer starts operating. · When printing for the first or second time after setup, the printer will take a minute or two before it becomes ready to print. e When the Authenticate screen appears, enter your administrator name and password. If you do not know your administrator name or password, click , then follow the on-screen instructions. (start Print Center if you are using Mac OS X v. 10. 2. 8) and then check that the printer name you want to use is shown in Printer List. For more detailed instructions, refer to the Mac on-screen Help. Note Restarting the computer while connected to the printer may cause the printer not to be detected. To resolve this, either unplug the USB cable then plug it back in again, or turn the printer off then back on again. d When the main menu appears, click Easy Install. i When the Installation Results screen appears, click Next. j Follow the on-screen instructions to register your product. Note When the User Registration screen appears, follow on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the printer. See Step 1- e on the front page. Now you have completed installation of the software. k When the Installation completed successfully screen appears, click Exit. Note · Select Easy Install in order to install the printer driver, on-screen manuals, and application software. Select Custom Install in order to choose the options you would like to install. [. . . ] Select Custom Install in order to choose the options you would like to install. · To install PhotoRecord and Adobe® RGB (1998), click Custom Install and follow the on-screen instructions. If you are using Windows Me/98, Adobe RGB cannot be installed. f When the main menu appears, click Easy Install. e When the list of applications to install appears, confirm the contents, click Install. Note Move the cursor over items to display explanations of each application below. If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. Now you have completed installation of the software. Note Select Easy Install in order to install the printer driver, on-screen manuals, and application software. [. . . ]