User manual CADDX NX-6

[. . . ] SECURITY SYSTEM NOTES Installing/Service Company _________________________________ For Service Call __________________________________________ Central Station ___________________________________________ Duress Code ____________________ FUNCTION CODES Function Code Controls Function This system is is not partitioned. EMERGENCY ACTIVATION KEYS (check if enabled) Fire Auxiliary Emergency Police PROGRAMMED FUNCTIONS Cancel Alarm Change Partitions Chime Communicator Test Abort Delay (V) Auto Bypass (V) Auto Instant Battery Test Forced Arming (V) Group Bypass (V) Quick Arm (V) Re Exit Siren Test (V) These features should not be enabled on UL listed systems. ENTRY / EXIT DELAY TIMES Exit Delay Time __________ Entry Delay Time _________ Secondary Exit Delay Time ________ Secondary Entry Delay Time _______ ZONE DESCRIPTIONS 01 _________________________ 02 _________________________ 03 _________________________ 04 _________________________ 05 _________________________ 06 _________________________ 07 _________________________ 08 _________________________ 09 _________________________ 10 _________________________ 11 _________________________ 12 _________________________ 13 _________________________ 14 _________________________ 15 _________________________ 16 _________________________ Note to installer: Identify the wireless zones on UL listed systems. THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN THIS BOOKLET. FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT WORKING PROPERLY. [. . . ] Quick Arm will allow the user to arm the security system in the AWAY mode by pressing the [EXIT] key, or arm in the STAY mode by pressing the [STAY] key. This feature is used for ARMING ONLY, and will not disarm the security system. CHANGING MODES WHILE YOUR SYSTEM IS ARMED Pressing the [STAY] key will turn on/off (toggle) a delay on entry/exit doors and turn on/off (toggle) the instant light. (Optional) Press the [BYPASS] key at this time to turn on/off (toggle) all designated interior zones. (Optional) When armed, pressing the [EXIT] key will start the exit delay, enabling you to leave the building. IMPORTANT The instant light needs to be off at this time if you plan on re-entering the building; otherwise you will create an alarm. You may restore an entry delay by pressing the [STAY] key again. DISARMING YOUR SYSTEM When you enter the protected area through one of the designated Entry/Exit doors, the keypad control will sound a continuous tone for the duration of the entry delay time, or until you enter a valid code. If a valid code is not entered before the end of the entry delay, an alarm will occur. (NOTE: If the red armed light is flashing during the entry delay, the alarm system has been activated in your absence. Leave the building immediately and call your alarm company and/or the police from a safe location. ) 8 CANCEL / ABORT FEATURE (Optional, see page 1) The cancel light will flash during an abort delay time. If a code is entered followed by the [CANCEL] key while this light is flashing, all abortable reports will stop the communication process. Entering a code followed by the [CANCEL] key during or after an alarm report to the central station will cause the cancel light to come on. It will stay on until the central station has received the cancel report. BYPASSING ZONES If you wish to bypass one or more zones, this must be done while the system is in the disarmed state. The following steps are used for bypassing zones: Step 1 Step 2 Step 3 Press the [BYPASS] key. (Example: Press the [1] key for zone 1, press [1] - [2] for zone 12. ) Press the [BYPASS] key again. The corresponding zone light will illuminate indicating the zone has been bypassed. Press the [BYPASS] key again -or- press the [#] key to exit the Bypass Mode. The bypass light will stop flashing upon exiting the Bypass Mode. Step 4 Step 5 Step 6 GROUP BYPASS By pressing the [BYPASS] key, followed by the [0] key, then the [BYPASS] key again, all zones that are designated as group bypass zones will be bypassed. UNBYPASSING To manually unbypass zones, perform the bypassing procedure on a zone that is already bypassed. NOTE: All zones will automatically be unbypassed each time the system is disarmed. TURNING THE DOOR CHIME ON AND OFF The door chime is turned on or off by pressing the [CHIME] key while the system is in the disarmed state. Each press of the [CHIME] key will toggle the chime feature on/off and produce a momentary ding-dong sound. [. . . ] The zone light(s) that is illuminated corresponds to the system fault(s) below: 1 Over Current Fault 5 Expander Low Battery 2 Siren Trouble 6 Expander Box Tamper 3 Box Tamper 7 Expander Trouble 4 Expander Power 8 Ground Fault Note: Faults 1 & 2 are global in nature and will affect all partitions of a multi-partition system. ZONE TAMPER - Press the [2] key and the zone light(s) will illuminate showing the zone(s) that are tampered. The zone light(s) will illuminate showing which zone(s) has a low battery. ZONE LOSS OF SUPERVISION - Press the [4] key and the zone light(s) will illuminate showing which zone(s) has loss of supervision. [. . . ]