User manual BRANDT TE1417B

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BRANDT TE1417B. We hope that this BRANDT TE1417B user guide will be useful to you.


BRANDT TE1417B : Download the complete user guide (4552 Ko)

Manual abstract: user guide BRANDT TE1417B

Detailed instructions for use are in the User's Guide.

[. . . ] 000 euros RCS NANTERRE 801 250 531 22 FR 02 EN 23 Dear Customer, You have just acquired a BRANDT hob and we would like to thank you. We have invested all our dedication and know-how in this appliance so that it would best meet your needs. In the BRANDT product line, you will also find a wide range of ovens, microwaves, ventilation hoods, ranges, dishwashers, washers, driers, fridges and freezers, that you can coordinate with your new BRANDT hob. Of course, in an ongoing effort to best satisfy your demands with regard to our products, our after-sales service department is at your disposal and ready to listen in order to respond to all of your questions and suggestions (contact information at the end of this booklet). [. . . ] The plug of the electrical outlet must be accessible after installation. 02 Mounting brackets The safety wire (green/yellow) is connected to the appliance’s ground terminal and must be connected to the ground lead of the electrical set-up. If the power cable is damaged, it must be replaced by a cable or a special kit available from the manufacturer or its AfterSales Service Department. Place your hob in the opening of the support cabinet, carefully pulling the table towards you. Reposition the burner heads, burner covers and pan supports on the hob. Connect your hob to the gas supply (See “Gas Connection” chapter) and to the power supply (See “Electrical Connection” chapter). If you wish, you can immobilise the hob using the four mounting brackets delivered with a screw (Fig. You must use the holes provided for this purpose, according to the diagram above (Fig. 29 Tip In order to easily locate the reference information for your appliance, we recommend that you note them on the “AfterSales Service Department and Customer Relations” page (this page also explains to you where to find this information on your appliance). 1 / INSTALLING YOUR APPLIANCE • GAS CONNECTION •Preliminary comments If your hob is installed above an oven or if proximity to other heating elements poses a threat of overheating the connection, you absolutely must insulate the cable in a rigid pipe. If a hose or soft pipe (in the case of butane gas) is used, it should not come into contact with a moving part of the cabinet, nor should it pass through a location that may become blocked. The gas connection must be installed in compliance with applicable regulations in the country of installation. € Gas distributed by pipe; natural gas, For your safety, you must choose from the three following connection options: — Connection with a rigid pipe made from copper and with screw-on mechanical connectors (G1/2 gas standard mark). Make the connection directly to the end of the elbow fitted on the appliance. € Connection with a flexible metal hose (stainless steel) with screw-on mechanical connectors (compliant with NF D 36-121 standard) whose service life is unlimited (Fig. € Connection with a flexible rubber hose reinforced with screw-on mechanical connectors (compliant with the NF D 36-103 standard) whose service life is 10 years (Fig. Warning When connecting your hob’s gas supply, if you have to change the direction of the elbow fitted on the appliance: x Change the gasket. Screw on the elbow’s nut, careful not to exceed a torque of 17 N. € Using the wrench provided, unscrew the injectors located under each crucible and remove them (Fig. € Replace with the corresponding gas injectors, in compliance with the placement of the injectors and the table of gas properties at the end of this section; to do so: — First screw them in manually until the injector locks into place. € Draw a line on the burner plate using a pencil at the place indicated (Fig. € Turn the wrench clockwise until the line appears on the other side(Fig. [. . . ] 39 3 / DAILY CARE OF YOUR APPLIANCE • MAINTAINING YOUR APPLIANCE MAINTENANCE. WHAT TO DO PRODUCTS/ACCESSORIES TO BE USED Of the spark plugs In the event that the spark plugs become . The crucible-shaped gas injector is located in the centre of the burner. Be careful not to obstruct it during cleaning, as this will undermine the performance of your hob. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BRANDT TE1417B




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BRANDT TE1417B will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.