User manual BOSCH SMI65M15EU

[. . . ] Dishwasher 9000 292 116 (8712-1) en Instructions for use en Index 4 4 4 4 4 4 5 5 5 5 5 5 6 6 7 7 7 8 8 8 9 9 9 9 9 9 10 10 10 10 11 12 12 14 14 14 15 15 15 15 IntensiveZone . Programme sequence indicator Remaining running time display Timer programming . 15 15 15 15 15 15 16 16 16 16 16 16 16 17 17 17 17 18 18 19 19 20 20 20 21 21 22 22 22 23 23 23 24 24 24 24 25 25 25 25 Safety instructions . . en Safety instructions Delivery Check the packaging and dishwasher immediately for damage caused in transit. [. . . ] There is a slight increase in the energy consumption. 15 en Programme sequence indicator 10 Your dishes are being cleaned. Your dishes are being dried. Switching off the appliance Short time after the end of the programme: Switch off ON/OFF switch 1 . Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display 11 . The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Interrupting the programme Switch off ON/OFF switch 1 . If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. To continue the programme, switch on the ON/OFF switch 1 again. Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. Press 7 + or ­ button until the displayed time corresponds with your requirements. To delete timer programming, press the 7 + or ­ button until is indicated on the digital display. You can change your programme selection at any time until the programme starts. Terminating the programme (Reset) Press START button 9 for approx. Switch off ON/OFF switch 1 . End of programme The programme has ended when the is indicated on the numerical value display 11 . 16 en Changing the programme When the START button 9 has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (reset). Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Intensive drying The final rinse uses a higher temperature which improves the drying result. Hold down programme button A and press START button 9 until on the digital display 11 is indicated . The LED for button A flashes and the digital display displays the factory . setting Press programme button A until the is indicated on factory set value the digital display 11 . To change the setting, Press the button C to switch intensive drying on or off . The set value is saved. Overall condition of the machine Check spray arm for grease and limescale deposits. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. [. . . ] 4 minutes press the START button 9 until is indicated on the digital display. (This prevents residual water from running into the machine control and damaging the programme sequence). Electrical connection Connect the appliance to an alternating current only, ranging from 220 V to 240 V and 50 Hz or 60 Hz via a correctly installed socket with protective earth conductor. The socket must be near the appliance and freely accessible following installation. Use only a residual-current-operated circuit-breaker which features the symbol. [. . . ]