User manual BOSCH SKS50E18EU

[. . . ] Dishwasher 9000 438 179 (8908) en Operating instructions Reset 3 sec. 10 9 8 7 6 5 End 9h 6h 3h Start End 1 2 3 9h 6h 3h 4 20 21 22 23 24 25 26 27 28 en Table of contents Washing the dishes . 13 13 13 13 14 14 14 14 14 14 14 15 15 15 15 16 16 17 17 17 18 18 19 19 19 20 20 20 20 20 20 21 21 21 21 21 21 Safety instructions . 13 en Safety instructions Delivery ­ Check the packaging and dishwasher immediately for damage caused in transit. [. . . ] ­ Keep pressing the Preselected starting time button @ until the appropriate display 3h, 6h or 9h is lit. ­ To delete the preselected starting time, keep pressing the Preselected starting time button @ until none of the displays 3h, 6h or 9h is lit. You can change your programme selection at any time until the programme starts. Terminating the programme (Reset) ­ Press START button 8 for approx. Switch off ON/OFF switch (. Changing the programme When the START button 8 has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. ­ Rotate programme selector 0 until the "Check water supply" display ` flashes. To change the setting, ­ By rotating the programme selector 0, you can switch on intensive drying (End displayh is lit) or switch off intensive drying (End display h is not lit). The setting is saved. End of programme The programme has ended when the End display h is lit. Switching off the appliance Short time after the end of the programme: ­ Switch off ON/OFF switch (. ­ Remove the utensils when they have cooled down. ã=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme ­ Switch off ON/OFF switch (. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 14 en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Filters The filters 1* keep large foreign objects in the rinsing water away from the pump. The filter system consists of a coarse filter, a flat fine filter and a microfilter. ­ Unscrew filter cylinder as illustrated and take out filter system. Overall condition of the machine ­ Check spray arm for grease and limescale deposits. If you find such deposits: ­ Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. ã=Warning Never use other chlorinated household detergents! [. . . ] Please note the system will not function unless the power supply is connected. Installation The required installation dimensions can be found in the installation instructions. ­ The appliance can easily be installed in a fitted kitchen between wooden and plastic walls. If the plug is not freely accessible, an allpole disconnector with a contact opening of at least 3 mm must be fitted on the installation side to satisfy the relevant safety instructions. Waste-water connection ­ The required work sequence can be found in the installation instructions. 20 en Removing the appliance Also observe the sequence of worksteps here. [. . . ]