User manual BOSCH SHE43C02WH INSTALLATION

[. . . ] Male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg. Accessory Parts Supplied Accessory parts for your dishwasher come in one or more plastic bags that are outlined below. NOTE: Make sure you save all the bags until you have completed your installation. Manual Set Bag A Manual Set Bag is provided with each dishwasher and includes: A Use & Care Instructions and Installation Instructions (both manuals may be included in a single "flip-style" book B Quick Reference Guide (select models) C Extra Tall Item Sprinkler D SHI and SHV Installation Template (SHI and SHV models only) E White Cotton Insulation Strip (SHY66C, SHX99A, SHE66C, SHE99C, SHX57C and SHV57C models only) Dishwasher Installation Kit A Dishwasher Installation Kit is provided with each dishwasher and includes: F Toe Panel Screws (2 black machine screws) Note: These screws are included, but not used on models with the Toe Panel Installation Kit. [. . . ] 2 Side Mount is used for countertops made of marble, granite, or other very hard materials that cannot be easily drilled. Bend the mounting brackets along the small holes and in the same direction as the two small tabs. Orient the mounting brackets as shown in Figure 10, and position the two small tabs on the mounting brackets over the two slots on the dishwasher's front corners. Push the mounting brackets down firmly to insert the tabs into the slots. Figure 10 Tip Over Hazard To avoid a tip over hazard, do not use the dishwasher until it is completely installed. When opening the door on an uninstalled dishwasher, carefully open the door while supporting the rear of the unit. Plastic Base Access Panel and Toe Panel (SHY66C, SHX99A, SHE66C, SHE99C, SHX57C, and SHV57C models only) The plastic base access panel and toe panel are in place on the dishwasher, but are not attached. Remove the toe panel first, as shown in Figure 11, then remove the plastic base access panel, as shown in Figure 11. Installing the 90° Elbow Fitting NOTE: The 90° elbow fitting is not supplied with the dishwasher, and must be purchased separately. If the dishwasher's hot water supply line is to be copper tubing, make certain the elbow has a compression fitting. Junction Box Preparation 1 Remove junction box cover (see Figure 13) by lifting the junction box cover up and off. 2 Remove the strain relief plate by removing the screw at the back of the junction box, as shown in Figure 14 and sliding the strain relief plate out. SHU/SHE Models - Accessory Panel Installation If you have an SHU/SHE model and have ordered an accessory panel kit, install the panel prior to sliding the dishwasher into place. SHI Models - Panel Installation SHI models come with additional mounting hardware and a template sheet with installation instructions. the stainless steel models of the SHI series also come with two extension pieces. The extension pieces are used to match the control panel height (Figure 16, "B" dimension) to the horizontal drawer line of the cabinets, and must be installed as shown in on the template sheet. The standard piece is used for drawer heights up to 6" (152mm); the long piece is used for drawer heights greater than 6" (152mm) but 6-7/16" (164mm) or less. If your drawers are taller than 6-7/16", you can either slide the extension piece in as far as it will go, or remove it and fit the door panel directly below the control panel. SHI/SHV Models - Panel Installation SHV models come with additional mounting hardware and a template sheet that will show you how to mount the panel. One side of the template shows how to mount a one piece panel; the other side shows how to mount a two piece panel. Decide which type of installation you want before proceeding with the installation. 1 Straighten and position the hot water supply line and the electrical supply cable as shown in Figure 18 so that they will align with their channels under the dishwasher base. [. . . ] If you are having a problem with your Bosch dishwasher and are not pleased with the service you have received, please take the following steps (in the order listed below) until the problem is corrected to your satisfaction. Contact your installer or the Bosch Authorized Service Contractor in your area. Please be sure to include (if you are writing), or have available (if you are calling), the following information: · Also, if you are writing, please include a daytime phone number where you can be reached. You will find the model and serial number information on the label located on the right-hand side of the inner door of your dishwasher, see Figure 1. [. . . ]