User manual BOSCH PMF 10.8 LI REV 5-2010

[. . . ] Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. B) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. unmodified plugs and matching outlets will reduce risk of electric shock. [. . . ] The lithium ion battery can be charged at any time without reducing its service life. The battery is equipped with a NTC temperature control which allows charging only within a temperature range of between 0 °C and 45 °C. Removing the Battery To remove the battery 2, press the unlocking buttons 1 and pull the battery out of the machine to the rear. Indication Continuous lighting, green Continuous lighting, yellow Continuous lighting, red Capacity >70 % 30­70 % <30 % When the battery charge-control indicator 4 flashes red, the machine is subject to overload. ) as well as during transport and storage, remove the battery from the power tool. There is danger of injury when unintentionally actuating the On/Off switch. Selecting the Application Tool/Accessory The following table shows examples for application tools. Further application tools can be found in the extensive Bosch accessories program. Accessory BIM segment saw blade Material Wooden materials, plastic, non-ferrous metals Application Separating and plunge cuts; also for sawing close to edges, in corners and hard to reach areas; Example: shortening already installed bottom rails or door hinges, plunge cuts for adjusting floor panels Sanding surfaces close to edges, in corners or hard to reach areas; Depending on the sanding sheet for, e. To remove the sanding sheet 13, grasp it at one of the tips and pull it off from the sanding plate 12. You can use all sanding sheets, fleece pads/ polishing cloth pads of the Delta 93 mm series of Bosch accessory program. English | 23 Selecting the Sanding Sheet Depending on the material to be worked and the required rate of material removal, different sanding sheets are available: Sanding disc Material ­ All wooden materials (e. Of rough, unplaned beams and boards For face sanding and planing small irregularities For finish and fine sanding of wood Grain size coarse medium 40 60 80 100 120 180 240 320 400 40 60 80 100 120 180 240 320 , for removing brush dashes, drops of paint and paint run) Dusts from materials such as lead-containing coatings, some wood types, minerals and metal can be harmful to one's health. Touching or breathing-in the dusts can cause allergic reactions and/or lead to respiratory infections of the user or bystanders. Certain dusts, such as oak or beech dust, are considered as carcinogenic, especially in connection with wood-treatment additives (chromate, wood preservative). Connecting the Dust Extraction (see figure A) Remove the application tool/accessory when mounting the dust extraction 18 (accessory). Turn the dust extraction in such a manner that the cams of the dust extraction engage into the corresponding recesses on the housing. fasten the dust extraction to the machine with the retaining clip 16 as shown in the figure. Pay attention that the felt ring 15 is undamaged and faces tightly against the sanding plate 12. An overview for the connection of various vacuum cleaners can be found at the end of these instructions. When vacuuming dry dust that is especially detrimental to health or carcinogenic, use a special vacuum cleaner. Inserting the Battery Use only original Bosch lithium ion batteries with the voltage listed on the nameplate of your power tool. [. . . ] There is danger of injury when unintentionally actuating the On/Off switch. For safe and proper working, always keep the machine and ventilation slots clean. If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for Bosch power tools. In all correspondence and spare parts order, please always include the 10-digit article number given on the type plate of the machine. [. . . ]