User manual BOSCH PEX 420 AE

[. . . ] 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. [. . . ] English | 17 The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns. Random Orbital Sander Article number Preselection of orbital stroke rate Rated power input Output power No-load speed No-load orbital stroke rate Orbit diameter Sanding plate diameter Weight according to EPTA-Procedure 01/2003 Protection class W W min-1 min-1 mm mm 420 215 4500­13000 9000­26000 5. We declare under our sole responsibility that the product described under "Technical Data" is in conformity with the following standards or standardization documents: EN 60745 according to the provisions of the directives 2004/108/EC, 98/37/EC (until 28 Dec 2009), 2006/42/EC (from 29 Dec 2009). For lower voltage and models for specific countries, these values can vary. Typically the A-weighted noise levels of the product are: Sound pressure level 84 dB(A); Sound power level 95 dB(A). The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. Depending on the material to be worked and the required rate of material removal, different sanding sheets are available: Material ­ ­ ­ ­ Paint Varnish Filling compound Filler Application For sanding off paint For sanding primer (e. , for removing brush dashes, drops of paint and paint run) For final sanding of primers before coating Grain size coarse medium 40 60 80 100 120 180 240 320 400 40 60 80 100 120 180 240 320 400 80 100 120 180 240 320 400 600 1200 Of rough, unplaned beams and boards For face sanding and planing small irregularities For finish and fine sanding of wood Automotive paint Masonry, stone Marble Granite Glass Plexiglas Glass-fibre plastics To remove the sanding sheet 6, lift it from the side and pull it off of the sanding plate 7. When attaching a new sanding sheet, remove any dust or debris from the sanding plate 7, e. The surface of the sanding plate 7 is fitted with Velcro backing for quick and easy fastening of sanding sheets with Velcro adhesion. Press the sanding sheet 6 firmly against the bottom side of the sanding plate 7. To ensure optimum dust extraction, pay attention that the punched holes in the sanding sheet match with the holes in the sanding plate. English | 19 Before opening the dust box 4, it is recommended to loosen the dust from the filter element by gently striking it against a firm support (as shown in the figure). Grasp the dust box 4 by the recessed grip, fold the filter element 15 upward and empty the dust box. Note: To ensure optimum dust extraction, empty the dust box 4 in good time and clean the filter element 15 at regular intervals. When working vertical surfaces, hold the power tool in such a manner that the dust box 4 faces downward. External Dust Extraction (see figure B) Slide the extraction adapter 16 onto the outlet piece 13. [. . . ] Exploded views and information on spare parts can also be found under: www. Com Our customer consultants answer your questions concerning best buy, application and adjustment of products and accessories. Only for EC countries: Do not dispose of power tools into household waste!According the European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally correct manner. [. . . ]