User manual BOSCH MCM 4100

[. . . ] The hoops (if fitted) consist of polypropylene (PP). Installation Install and connect the appliance according to the installation and assembly instructions. The dishwasher must NOT be connected to the power supply during installation. Ensure that the protective conductor system of the domestic electricity supply has been installed correctly. Electrical connection conditions must correspond with the specifications on the rating plate of the dishwasher. [. . . ] Before you re-insert the basket, ensure that it is at the same height on both sides. Otherwise, the appliance door cannot be closed and the upper spray arm will not connect to the water circuit. 11 aus Detergent compartment with measuring marks The side of the detergent compartment is marked with lines to help you determine how much powder to add. The capacity of the detergent container is 15 ml up to the bottom line and 25 ml up to the middle line. If you are using the upper rack only, or if your dishes are only moderately dirty, it will normally suffice to employ a reduced amount of detergent than otherwise recommended. Press down the lid (1) until it clicks shut (2). 40 ml 25 ml 15 ml Important If the lid on the detergent compartment is closed, press the release lever to open the flap. If you are using detergent in tablet form, read the manufacturer's recommendations on the packaging in order to determine where the tablets should be placed inside the dishwasher (e. g. Make sure that the lid on the detergent compartment is closed, even if you are using tablets. Adding detergent Tip detergent powder into the corresponding compartment 29 . Please observe the manufacturer's instructions printed on the detergent packaging when determining the correct dosage. If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Switching the dishwasher ON Turn on the tap. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 6 is pressed The numerical display 4 shows the expected duration of the programme. Press the TIMER button as many times as necessary until the numerical display shows the required delay. To erase the time delay setting, keep pressing the TIMER button until appears in the numerical display. You can change your programme selection as often as you like during the intervening period before the dishwasher starts up. Cancel programme (Reset) Only when the master switch is ON. Press the A and C buttons simultaneously, and hold them pressed for approx. To restart the dishwasher, set main switch 1 to ON again and select desired programme. 16 aus Changing the programme It is possible to change the programme within 2 minutes after you have switched the dishwasher on. Should it be necessary to change the programme after this period, the programme cycle that has already been begun (e. g. The new remaining time displayed is the sum of the remaining time from the preceding programme cycle and the remaining time attributable to the new programme that has been selected. Additional functions * * on applicable models Pre-Soak * The Pre-Soak programme option serves to perform a pre-soak cycle before the main programme. If you wish to pre-soak the dishes, this programme option must be selected by pressing the "Pre-Soak" button before the programme starts. 5 g poured onto the inside of the door. Quick * Pressing the "Quick" button provides a short wash cycle by curtailing the drying phase and the washing time. The washing and drying performance will be reduced with the Quick programme option. Washing contents of UPPER RACK only * If you have a small number of dishes to wash in the upper rack (e. g. Add a reduced amount of detergent compared to that which is recommended for a full load. Washing contents of LOWER RACK only * If you have a small number of dishes to wash in the lower rack (e. g. [. . . ] Smears left behind on glasses and cutlery; glasses have acquired a metallic appearance Amount of rinse-aid set too high. aus Customer Service Please call your local service agent, if you are not able to resolve any problem yourself. The name of your nearest service agent is shown in the Customer Service address list. When you call, please provide details of the model number (1) and the production (FD) number (2) which are shown on the nameplate on the appliance door. Information Disposal Old appliances are not worthless rubbish. To prevent children from locking themselves in the appliance and suffocating, destroy the door lock and childproof lock (if fitted). [. . . ]